GTWN5650F2WS General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wallace from Delbarton, WV
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
My washer started leaking water out of the bottom.
I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harm from JENISON, MI
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
tube would fill, but agitor would not ingage
replace lid switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from BLUFFTON, SC
- Parts Used:
- WH13X10053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Water Dripping into washing machine when not in use. Turned off water supply to back of washing machine and dripped stopped.
turned off off water supply, unplug plugged washing machine and removed back panel to access triple water valve. removal was easy that took about thirty minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from LANEXA, VA
- Parts Used:
- WH23X10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Drain pump not working. Washer would not drain or advance to spin cycle.
Repair video is spot on but does not emphasize securing the drain pump to the washer before reattaching hoses. This holds the pump in place allowing you to compress the hose clamp while pushing on the hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GABRIEL from LA QUINTA, CA
- Parts Used:
- WH12X10334, WH01X10302, WH01X39337
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
tub moving allover the place
replaced broken straps all 4. washer not working ]. replaced lid switch with wire harness.replaced bad old belt.working fine now. my wife is very happy. thanks for your videos and how to do the job right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donn from WIMAUMA, FL
- Parts Used:
- WH43X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fitted sheet got stuck under the agitator
Reach down and grab the base of the agitator with both hands and yank up with slightly more pressure on the left or right, whichever side you prefer. This will break loose the holding clamps/pull straight up. To re-install: align slots and push down until it snaps. Simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from PLAINS, MT
- Parts Used:
- WH41X22935
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Small wire had tried spin out of drain pump. Wore pin hole in the rubber drain hose....
Unplugged...Removed back from washer...Using nut driver-cordless drill...Inspected hose-found leak....Removed hose with pliers & screw driver.....Than dried the hose...& than for temporary fix (for the wife to continue washing) used some Epoxy for rubber.....Than ordered new part. Received and reinstalled replacement. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Longmont, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Straps had stretched with age.
Removed the front panel. Removed the washer top. Removed and replaced each strap. Very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Traci from TRACY, CA
- Parts Used:
- WH01X10302
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Washer won't agitate or spn
Followed the instructions on repair clinic video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from EVERETT, WA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
drain hose was leaking near pipe in wall
Pull hose out from wall and drain water into bucket. Remove two screws from back of washer holding on the clip. Pull hose out from washer its in there about 3 inches or so . If you order a new clip will make this even easier it's only $3.87 and I didn't realize I needed it. So, I just cut the old hose with a small saw near the clip so I could remove it and reuse it. Just slide the clip onto the end of the new hose - it fits into one of the grooves-I just made a note of where that was before removing from old hose. Then replace the two screws on the clip going to the back of washer. Put other end of hose into pipe in wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from LAKE ST LOUIS, MO
- Parts Used:
- WH38X10019
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The bolt holes of the new drive shaft assembly come unthreaded
This is a normal condition; the old bolts are self-tapping so simply align them well, I used a drill-driver to get them started and completed tightening with a socket wrench. (Also the new drive shaft assembly comes with a tub seal, so you don't have to order a separate one.) I do think it would be better if the drive assembly came with 4 new bolts.
The instruction video was immensely helpful, Thank you.
The instruction video was immensely helpful, Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WOBURN, MA
- Parts Used:
- WH02X10383, WH2X1198, WH2X1197
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Noisy on spin, leaking water
Could not complete repair. The pulsator was rusted on the shaft, used wd 40, finally pried off the shaft. The hub nut was so corroded on the shaft I could not remove it. Reassembled the Machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from LAKE ST LOUIS, MO
- Parts Used:
- WH2X1198
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
hammering on the tub nut wrench rotated the drive axle & pulley
I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammed from Berkeley, CA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drain hose was leaking
Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CHARLESTON, SC
- Parts Used:
- WH13X10053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
would not mix properly and/or fill properly
Easy as can be. Similar but not exactly like the YouTube videos, but close enough. Biggest problem was pulling the filler tube off of the mixer and re installing the tube. Nothing to get worked up about.
Was this instruction helpful to you?
Thank you for voting!