WLSE4210A0WW General Electric Washer - Instructions

I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.

Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.

I decided without see exactly where the water was coming from to replace the pump and all the drain or inlet hoses, connectors, whatever carried water due to the age of the machine, almost 17 years old. I also decide to change the tub seal.
1. unplug
2. disconnect water supply
3. remove back of washer
4. laid washer on its front on a rug
5. removed the drain and filler hoses (3) different hoses and all new clamps
6. closed up everything, hooked up everything ran short cycle

WHEN THE PUMP STARTED SO DID THE WATER POURING OUT FROM UNDER THE WASHER, MORE THAN BEFORE I CHANGED OUT THE PARTS

I decided the tub seal was leaking. It was a logical decision and it was the last part that carried water that I didn't change.
1. remove front panel
2. remove top panel
3. remove electrical connection inside pane and remove entire top panel
4. remove agitator and agitator cup
5. remove top ring that hold inner liner
6. here is the problem, a special tool is required to remove the tub seal nut or a 1-11/16" socket that I didn't have
7. tried a new pipe wrench and rust buster taking care that the nut is soft metal
8. decided to purchase the correct tool(socket) and put everything back together to do two weeks worth of laundry
I left the front panel off to pinpoint where the water leaks was and when the pump started there was no leak in the washer. However, water was pouring across the floor.
I found that the house drain pipe was cracked on the top and back. This was on the outlet side of the trap. I would have never suspected the drain (PVC) with no stress or load on it to crack across the top of the pipe.
So anyway, $240 later for washer parts and $6.47 for a new piece of PVC I no longer have a problem, wrong!
Started a load of laundry and the washer will only fill for a small load.
1. Removed the front panel
2. removed the tube to the fill switch thinking there was water in it that's making the switch think its full when its not, NO WATER.
3. Shot air in the tube and made sure the switch clicked audibly
4 Started the washer with the fill switch tube off and waited for waited for water to start flowing out and then hooked up the tube and it shut off the water with a full load. Everything worked.
Tub seal still not changed but no leaks.

After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.

followed the video you provided and it was easy!

At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push

Just push knob on less than 4 seconds

Took new one out of package, and push it on. 4 seconds!

I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.

After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY

I was going to replace the washer. .. I am a cabinet maker and pretty good at what I do. I have to admit before seeing the video I was out of my comfort zone with this repair. I was shown not only the part needed and that you folks had the part in your inventory on hand. I was pleased to see how inexpensive it was $7.40. I had it shipped for $8.70. I ordered online at 2 pm. the part arrived the next day at 1 pm. AMAZING!. I spent ten minutes making the repair. The machine is now back to it's like new self! Regards, MichaelAndrews.biz

I put my fingers under the agitator and pull up , this pulled it off the couplier, then I used a 11mm wrench to remove the bolt that holds the couplier in place and pulled the couplier off, the new couplier didnt arrive until after I went to work but my wife had it all back together when I got back home,I told her what to do and she said it only took about 10 mins. to get together, very easy.

I just added the agitator coupling and screwed it in.

I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I received the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!

The part came very fast and was easy to install, I pulled off the agitator and removed one bolt, replaced worn out part with new part and put the new bolt that came with the part in. Reatached the agitator and washed some clothes. done