FFFW5000QW0 Frigidaire Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Manny from Old Bridge, NJ
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing machine wouldn't go into final spin.
First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENN from MADISON, IN
- Parts Used:
- 134370000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
i broke the soap dispenser on my washer
love parts select have used them several times for parts great company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lancaster, CA
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washer drained withn no spin
Remove top of washer, remove door lock assembly,install new assembly replace top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from SEVIERVILLE, TN
- Parts Used:
- 131763256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Our washer would not do the final spin. Error code was 47, which is door not closing
I removed 2 screws from the the top back of top. Removed the cover. Removed the 2 screws holding the door lock assembly.Removed the door lock assembly, disconnected the 3 wiring harnesses. Connected the wiring harnesses to the new door lock switch assembly. Installed the new unit in the door lock, reinstalled the top.Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from OROFINO, ID
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer would not drain or spin
Removed the 4 screws holding the top on. Pulled top forward to release front catches and stood top up out of way. Removed 2 screws holding door lock. Could not unplug wire plugs from door lock because wires too tight. Removed 2 screws holding lower front panel and removed panel. Pulled door lock down and unplugged old lock and plugged in new lock. It was easier to position door lock to reinstall screws by working from top, so top removal wasn't a total waste of time. Reinstalled front panel and top. Machine works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from THOMPSONVILLE, MI
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer woild not spin out left clothes sopping wet
It was very good. They should have mentioned about the wire and spring to remove the rubber strip though. Found out about that in comments! Otherwise, very good!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from ST MICHAELS, MD
- Parts Used:
- 131763256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Washer door wouldn't lock so it would not run
Watched a u tube video and did it myself and I'm a 58 year old woman who has never worked on a washer before!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica Ramaker from SAINT PAUL, MN
- Parts Used:
- 131763310
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Door Strike
Very basic replacement- 2 screws in and out. The part did not come with screws to be sure to save them if you remove the broken part ahead of time to make the process smoother.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from DELTONA, FL
- Parts Used:
- 134618213
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
While using washer a E9F code appeared and stopped working.contacted parts select trouble shooting site they told me what it was ordered the part they were right on!back washing again thanks so much for the help!
Did it with no problems at all just followed the video step by step worked great done in 1hour!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Jacksonville, FL
- Parts Used:
- 131763256
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
easy repair. I went to the back of the washer and removed the two(?) screws that held the top panel on. Then moved to the front of the washer and unscrewed the two screws in the door frame holding the lock assembly. Pulled it up and out from the top of the washer and disconnected the three wire connections. Then I just reversed the process with the new part. It all worked great. This website rocks...
Phil
Jax, FL
Phil
Jax, FL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Wichita, KS
- Parts Used:
- 131763310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch on door broke. It is made of plastic and just broke off.
just unscrewed the old one and put a new one on.
I bought two just in case this one breaks too.
I bought two just in case this one breaks too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Brandon, FL
- Parts Used:
- 131763256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Washer would spin in any cycle
Tilted the washer back to take the 2 screws off the bottom to remove bottom plate. Took the 2 nut screws from the bottom of the face plate so that the front of the washer would pull slightly out from the bottom. Removed the 2 screws from the door stricker plate which allowed the door lock assembly to come out through the side of the washer. Unplugged 3 plugs, plugged the new switch in and slid it back into place, put the 2 screws back in to hold it. Reattached the front and the bottom plate. And bingo done. It worked and saved us about $245.00. Very happy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery David from Chesaning, MI
- Parts Used:
- 131763310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bkn door strike
Very simple hardly worth writing about.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cos Cob, CT
- Parts Used:
- 131763310
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door on washer broke lots of laundry to do!
I was amazed at how quickly my part came for the washer and it came to me on a Saturday
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Colorado Springs, CO
- Parts Used:
- 131763310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door striker was broke
unscrewed the 2screws from the striker on the washer door first. Then put screwed new striker on door with its new screws. It was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!