BKFW4271MT0 Frigidaire Washer - Instructions

Wow - that was quite the project. The directions that come with it are not the most clear. First of all, when it is time to pull the bellows and spring off, just plan on pulling as hard as possible. I used some Channel Locks to grab the bellows, as my hands just couldn't hold on. Two people would make it easier. The toughest part is getting the spring back on. My advice is to remove the yellow tubes from the black spacers and just use the black part.

Unscrewed two phillips head screws, removed damaged part, screwed on replacement part. Presto! Washer works again. I especially appreciated receiving the part less than 48 hours after I ordered it with only regular shipping charge.

After some research online about my Frigidaire Washer, I pre-determined that the problem could likely be the lock mechanism. I ordered the part and it arrived within 3 business days. My son removed the screws from the back of the washer, slid the top off and removed the old part and replaced it with the new part. It took about 20 mins. The machine is now working properly again. The door catch that I ordered did not work with the door lock I ordered. However, the old door catch that was still in good working order does work with the new door lock and switch assembly that I purchased.

took the top off removed the old one and put in the new one.Works great!!

Removed two screws, installed new piece.

First we took the pump off and it was full so we hoped replacing it as the fan blades were broke and it didn't help. We replaced the control board and that didn't change it either. So I checked here and the door strike and door switch could be the problem so I ordered and put them on that was the problem. Thanks so much. Instructions were well printed and the job was about 5 minutes to replace. The washer works perfectly. We should have started with these parts first and it may not have cost so much.

1. Remove the spring clamp around the tub seal. 2. Pull back the tub seal in the area by the door lock switch. 3. Remove the switch assembly by removing two Phillips screws. 4. Remove connectors from switch. 5. Install connectors onto new switch. 6. Mount new switch on washer with two Phillips screws. Reinstall tub seal making sure to tuck it correctly on the washer frame. 7. Reinstall spring clamp.

Removed 2 screws , unplugged the old switch , replaced with new one and secured with screws . Easy !!

I unscrewed the two screws and replaced with new door striker and used the same two screws I took out. It took me seriously less than 2 minutes and I am a woman!

I took off the broken part with a screw driver. I easily found the needed part on your website. After I ordered the part, it came within 2 days. It was the correct part and was replaced within 10 minutes of opening the package. Thanks for the great, easy and quick service!

took the 2 screws out, removed the old and screwed in the new.Piece of cake. What stod out in the process was Part selects follow up with email and video of how to replace. They are great....

unscrewed (2) screws, took broken piece off and screwed new piece on with the (2) screws. Keep your old screws because part does not come with screws.

Remove the broken striker, screwed in the new one in less than 2 minutes...this is the second time it was replaced...the first time I was still under warranty...he took about the same amount of time to install ...I ordered 2, because I know it will be broken again....

It is a front load washer with a dryer stacked on top of it.Insaw a video on u tube. I took a neddle nose pliers ang took a spring loaded metal ring off that is holding the grey rubber boot on . I peeled it back just enough to reach ih and get the door lock in hand.I then took a phillip screw driver and removed the two screws un the front off holding the door lock..I then reversed instructions,and put the new lock in.The complete job took lease than 5 minutes,and the part did the trick. My washer works as good as new.

first problem is the hinge get worn or broken from being leaned on. second problem is the door gets slammed trying to close it braking the striker. to fix the problem 2 screws for the striker, to permanently fix repair door hinge. and a big thank you for the people who own and or run this site. my order was lost and they got the part to me the next day.