4GNTW4400YQ2 Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from KISSIMMEE, FL
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer shaking and banging loudly during spin cycle
Replaced the suspension rods
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from BURIEN, WA
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Shakes and moves | Noisy
Followed video on your web site, and used that for ways to fix, good directions. If I was more organized it prob would of taken about an hour or less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from BEECH ISLAND, SC
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Springs worn out on the suspension rods. (Noisy drum in spin cycles)
The video posted on this site will walk you right through the repair. Great service. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from OROVILLE, WA
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Extreme imbalance
This washer would not go into spin cycle without going out of balance no matter how we arranged the contents in the drum. We were looking to buy a front loader when I happened open this company with video instructions and positive comments from other people with the same issue. For the cost it was worth a try. Following the video and in less than one hour the washer was back in service. It now operates like the day we installed it new. Highly recommend this fix which should save you hundreds on a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BRISTOL, CT
- Parts Used:
- WPW10006384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Belt needed to be replaced
Took the Cover off and installed belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Dundalk, MD
- Parts Used:
- 285809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator was free spinning
Followed instructions, which were included with the parts, and the repair was a snap. So easy a caveman could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Russiaville, IN
- Parts Used:
- WP3951744
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The washer was not agitating
I removed the Softner dispenser and used a socket wrench to remove the entire agitator. Then replaced it with the new one. It was so worth doing it myself. I cost us about $50.00 and that would have been the cost of having a service call. without parts and labor. I was thankful that it was an easy job and one that I could figure out. It saved us a ton of money. Since I don't know the names of any of the parts on this machine, it was nice to have pictures that go along with the parts online. It allowed me to order the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jimmy from southport, FL
- Parts Used:
- 285809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
top agitar dogs failed to grip anymore,just worn
pulled the new ones out of package,same part nice instructions,couldn't get any eaiser,thanks guys for the very fast shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from san clemente, CA
- Parts Used:
- 285809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The top part of the washer was not ratcheting to turn clothes over in wash tub
removed the softner insert, pulled the plastic seal, loosened and removed the 7/16" bolt that holds the paddles in the tube. removed the top part of the paddles/agitators, removesd the old cams and replaced with the new. it works awesome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from west covina, CA
- Parts Used:
- 285809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
top part won't turn by it self
pull the top cap off, then the inner cap off, then use the 10mm socket to remove the nut., then pull the whole thing off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from MITCHELL, SD
- Parts Used:
- WP3951744
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Agitator, not working, spins freely on drive shaft
I was emboldened after reading other reviews by how easy it was to replace the agitator in my Whirlpool, with comments like "it took less than an hour". Well, that might be true for some... The video also made it look easy, so I ordered the replacement part. I did not disassemble the machine in advance but I did enough troubleshooting to determine that the clutch was fine, but the agitator failed to spin during operation. When the part arrived I followed the video, but I was unable to loosen the retaining bolt. The failure of the agitator was a result of stripped gear on the inside of the agitator, so it just spun loosely or, during the wash cycle, not at all. Because the gear teeth failed to grip, I was unable to use the agitator to hold the shaft stationary while loosening the attaching bolt. My only option was to cut the plastic agitator away from the shaft using a rotary cutter, being careful not to damage the shaft or the bolt. This was a painful, time consuming job but, with patience, it can be done. Have a shop vac handy because you'll have to stop on numerous occasions to vacuum up plastic pieces and dust, so they don't slip through the small holes in the drum and clog your drain. The problem was compounded because during the initial installation they had used excessive amounts of Loctite and the bolt was glued pretty tightly to the shaft. Anyway, after approx. 4 hours of troubleshooting/repair work the washer is back in operation, and I still saved money on the deal, so I'm a satisfied customer..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from OLD FORT, TN
- Parts Used:
- WP3951744
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Bad aggitator
Replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ALPENA, MI
- Parts Used:
- 285809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The dogs were stripped and they would'nt grab the agitator
Popped the old one off and replaced it, piece of cake !
Was this instruction helpful to you?
Thank you for voting!