NAH6800AWW Amana Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
One of the drum baffle's boke from it's mount
Removed old broken plastic grommet's and installed two new plastic grommet's. Attached new baffle using old screws. Used a short piece of picture frame wire to install the two new grommets by fishing them into place with out removing the washer drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Huntington Sta., NY
- Parts Used:
- 22003856
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Motor did not have the ability to rotate washing machine drum.
Removed old motor installed new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PLACERVILLE, CA
- Parts Used:
- WP22003834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water continued to fill up in the washer when it wasn't being used
I was able to open up the top lid on the washer to gain access to the water inlet valve. I changed it out and now water doesn't continue to fill up the washer when it isn't being used. Problem solved. Great video on how to gain access to the water inlet valve.
Was this instruction helpful to you?
Thank you for voting!
Washer was so loud in the spinning cycle it sounded like a jet was taking off
We took the washer completely apart. Replaced the bearings, pulley and
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.
belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
It was well worth the time and effort we put into it. It works like a chime
and is very quiet . Silence is golden ! Hopefully it will work another 18 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Bethel, CT
- Parts Used:
- WP22002083
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water leaking around washer
First ya have to find the problem that takes time.
Pulled the front off via the four screws, two on the door and two on the opp side. Removed the two top hold down brackets that hold the top on (on the front), popped out the four screws for the detergent and the top hinged up, The hose was right there. Removed the two hose clamps, found the crack ordered if from you guys.(very fast) slapped it in and put a load in.
Pulled the front off via the four screws, two on the door and two on the opp side. Removed the two top hold down brackets that hold the top on (on the front), popped out the four screws for the detergent and the top hinged up, The hose was right there. Removed the two hose clamps, found the crack ordered if from you guys.(very fast) slapped it in and put a load in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from KASSON, MN
- Parts Used:
- WP22003834
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Tub slowly filled with water when washer was off.
Unplugged, turned water off, removed hoses. Removed screws, unplugged wires, disconnected interior hose and replaced old water inlet valve with new one. Reassembled. Repair was completed by my 17 yr old son in 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from VAIL, AZ
- Parts Used:
- WP25001052, 12001788
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer not draining some of the time resulting in the code ND being displayed.
The replacement of the drain pump was very easy. I will not go into detail, just follow the video installation provided on this site and you will have no problem.
I decided to replace the drive belt since I was into the back of the washer. The video on this site was spot on, however I did have to apply a lot of effort putting the new one on. My old belt was stretched out considerably and at first thought I had a wrong replacement belt. Number on the belts confirmed it was correct. Just had to walk the belt on the larger pulley and it will fit.
My washer is running like a new one!
I decided to replace the drive belt since I was into the back of the washer. The video on this site was spot on, however I did have to apply a lot of effort putting the new one on. My old belt was stretched out considerably and at first thought I had a wrong replacement belt. Number on the belts confirmed it was correct. Just had to walk the belt on the larger pulley and it will fit.
My washer is running like a new one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Durango, CO
- Parts Used:
- WP22003834
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
I stripped the plastic threads on the old water inlet and so I had to replace it.
Unscrew the screws holding the soap/bleach/fabric softner in place. Unscrew the door hinges.Unscrew the white plastic clips that are to the right of the door. These hold the front of the washer in place. Once these are removed, you can pull the front of the washer away from the door opening. It leans out from the top and you can remove the entire piece from the clips that hold it in place at the bottom. Then you can unscrew the screws to the top left and top right that hold the top of the washer in place. Once these screws are removed, you can lift up the top of the washer and lean it back revealing the water inlet valve w/thermister. All the electrical connections are easy clip off/clip on. The hose clamp is the typical screw type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from EL Paso, TX
- Parts Used:
- 12002533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Torn and moldy boot seal
We followed the directions in other people's repair stories here. Removing the spring was a challenge, as was getting it back on! The rest of the repair was simple. Be patient with removing the soap dispenser. Ours had some plastic cords connecting it to the frame which we didn't anticipate, and we broke them because we didn't see them.
We're going to try that new Affresh product in the hopes of avoiding this repair again in the future. We never washed anything harmful in the washer. This seal becomes moldy and deteriorates with time. Using bleach to kill the mold only speeds the process.
We're going to try that new Affresh product in the hopes of avoiding this repair again in the future. We never washed anything harmful in the washer. This seal becomes moldy and deteriorates with time. Using bleach to kill the mold only speeds the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from N LAS VEGAS, NV
- Parts Used:
- WP25001052
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set
Thought pump was the problem making noise but the noise is still there might try changing belt and motor isolator hit ,the noise is like a growling noise before pump starts to drain
Followed a video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from N LAS VEGAS, NV
- Parts Used:
- 12001788
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Noisy
The motor isolators went in with no problem ,but the drive belt went on very tight , your how to video shows how. Easy the belt went on , when I called your store I was told that is the only size belt for the machine model mah5500bww,
Thank you Bill
Thank you Bill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kirk from CHARDON, OH
- Parts Used:
- 12002533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Washer leaking water - bellows had a hole in it.
Using the video tape (YouTube URL) provided, I went step by step and replaced the bellows with no problem. No water leaking..the toughest part was putting the spring back on, it takes some coordination and muscle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from FOLSOM, CA
- Parts Used:
- 12001788
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burn smell during spin cycle.
I followed the instruction of using a tie strap to secure belt to drive pulley and turn pulley to place belt on pulley. Worked great. Done in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from PORTAGE, WI
- Parts Used:
- WP22003834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Hot Water Inlet Valve Stuck open!
After watching the repair video, The job became very easy. Thank you parts select, the only thing i didn't like, was the shipping cost. thought it was a little high for such a small and light part..
Was this instruction helpful to you?
Thank you for voting!