WET4124HW0 Whirlpool Washer Dryer Combo - Instructions

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

Checked on your website for common problems w/this model dryer,highest probability was the thermal fuse being blown,so I ordered one & checked the vent for being plugged,no problem there,removed the back of the dryer replaced the fuse(very easy to do)put everything back together & started it up...all set now.Thanks for your help

First I pulled the dryer away from the wall, after which I disconnected the power and dryer vent. I then removed the eight screws holding on the back of the dryer. Next, I disconnected the two wires to the part and unscrewed the mounting screw. I then removed the bad part, replaced it with the new part, and reversed the above steps.

How I did the repair is of little importance. What is important and impressive is the level of service your company provides. You must have a fantastic system in place and a team who has bought into the concept of providing the best customer service possible. I have been a Manager for over 15 years and would go home proud and would sleep well every night if my team offered the service your team does. Please share this feedback with them and take the time to shake the hand of everyone who was in the chain of service of this order. Smile and tell them Russell C says well done and thank you. Your team made my life easier and I feel appreciated as a customer of your Company.

I studied the wiring diagram on the back of the dryer. I diagnosed a bad thermal fuse (no continuity). Found the part online at Part Select. The part came a few days later and I was back in business. Great Service.

It took me 5 minutes to find PartSelect's site, read the comments about the most common problems and identify the solution. The exploded views were a great assist, as it wasn't obvious where the thermal fuse is located or which access panel to remove.

It took less than 5 minutes to remove the rear panel and install a temporary jumper to verify the blown fuse was the only issue. With the new fuse in hand, replair took another 5 minutes.

A word of caution to anyone replacing is fuse - I found that the exhaust vent pipe to the wall was full of lint and nearly blocked. This is a potential fire hazard. While enough air was passing through the flapper vent to make it look like it was OK, the exhaust resistance is what caused the overheating and made the fuse blow.

I spent more time cleaning out the vent pipe than replacing the fuse, for a total of 25 minutes. I strongly urge all dryer owners to physically inspect the exhaust duct annually.

PS Drying time has decreased by 30-40% since the repair.

After receiving the part I pulled the dryer out for easy access. Used only a nut driver to remove back cover and the part to replace was easily identified. Then it took a little while to remove all the dust and other particles that had built up over the years. The actual replacement of the part only took a couple of minutes. Reattached the back cover and put back in place. Turned on dryer and I now had heat. Easy fix.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and although not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.

I made sure air vent was clear and clean. I removed front panel of dryer unit, located fuse, removed wires, tested fuse with ohm meter, which was defective. Tested new fuse placed back in dryer reattached wires. Cleaned out inside of dryer, replaced front panel. Now works like new.

Replaced the drum support rollers and a thermal fuse and the dryer works great now.

removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in business

The Termal Fuse did not solve the problem. Ordered a heating element so I hope its that

just replaced parys

Attempt to start dryer normally. Turn timer dial to high heat setting. Press the Push To Start button. Verify plug is secure in wall outlet. Got to breaker panel to verify breaker is not tripped. (Sometimes breaker may trip but visually appear no to be tripped). Reset breaker to maker sure breaker is in the on position. Attempt to start dryer normally. If dryer did not start proceed. Get a multimeter. Remove plug from wall outlet. Slide dryer from wall. Remove exhaust duct from bottom of dyer. Use multimeter to check voltage at wall outlet. Verify 120 to ground and 208 between hot legs. Remove rear cover if main dryer unit and rear of control unit. Connect the multimeter to rear of control panel rear of push button. Turn meter to ohm setting. Push the start button to see if there is continuity. Release the button to verify no continuity. Next major part of curcuit is the thermal fuse. Look on lower left area of dryer. With multimeter in Ohm mode place the leads on the light blue wires. If no continuity replace thermal fuse