WET4124HW0 Whirlpool Washer Dryer Combo - Instructions

I first watched the helpful video on website. Un- plugged the dryer. I removed the back cover and tested the thermal fuse with the multi meter. Ordered the replacement part. Replaced the Thermal Fuse, and put the back cover back on. This was a very easy fix! It takes longer to remove the back cover of the dryer than it does to replace the fuse. While I had the back cover I used my air compressor to blow out any lint. This dryer is as good as new now. this site fast shipper, Great website.

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

replaced internal dryer filter housing

First I removed the top back plate and found the electrical schematic, found the fuse and themostat. Went to Whilpool web site found exploded parts list to identify part (fuse)

removed fuse and tested with MM for an open. It was. Shorted the leads to verify that the Dryer operated. Found your site and was easily able to identify the part from the excellent description and pictures. Ordered it, installed it work great thanks

I guess you could say I went through the process of elemanation, first I replased the thermostat,removed 2 screws pulled off 3 wired with a pair of pliers put them on the new one, still no hot air so I replaced the fuse, took out 1 screw removed 2 wires and placed them on the new fuse, still no hot air, finally I replaced the thermal cut-off switch and WOW that was it hot air was blowing again, the process was very easy I ordered everything from parts slect and they were here the next day, only had to take the back off the dryer with a nut wrench, locate the thernastat, fuse and thermal cut-off which was just above the heating coil I removed 1 screw pulled off 2 wires and place them on the new one. very easy and the repair storys really helped locating the problem

So I opened the back up, and looked down the flame shoot and I could see that the igniter was never glowing red. (You can actually see the red glow of the igniter when its working right, then you here the solonoid click and flame. But again all this when its working correctly.) So anyway, no heat no glowing red.

I took the voltmeter out, grounded 1 lead and just followed the voltage (using the schematic provided), through the switches, yada yada trying to trace how far it got.

Voltage got to 1 side of thermal fuse, but not to other side. Bingo. Disconnected fuse and did continuity check - open. All of this took diagnosing took 1/2 hour to hour. Not really counting toward fix. Ordered the part at parts select. Put a jumper over the fuse so that clothes could still be dried (probably not recommended but it works). Part arrived in 2 days. Didn't even put the back panel on.

The part is right on the back. 1 screw, 2 space terminals. Takes all of 3 minutes to replace. Then another 5 minutes to put the back panel on and vent hose back on. Most of that is because you are working in a cramped space. (I don't have the biggest laundry room.)

Can't beat parts select!

Parts select + a little know how, saved me about $400.

I removed the back of the dryer, removed the single screw holding the fuse in place and checked it for continuity. It didn't work, so I placed an order and 3 days later I was back in business. the replacement took about five minutes.

removed cover then pulled wires with a plier, unscrewed the fuse and installed new fuse then put back cover plugged in power cord, fired dyer and run dryer for 2 minutes and felt warm air coming out of the exhaust.

this was a super easy job! i unplugged the dryer, removed the back panel, located the fuse on the bottom left side, replaced it, put the panel back on, plugged it back in and IT WORKED! this was the first appliance repair job for me and i am so glad i found this site. it probably saved me $100.00 or so doing it myself. thank you!!!

I watched the video several times before beginning, which was very helpful. As I didn't have the tool that was recommended in the video, I used pliers, which although took longer, worked out fine. I also used pliers to pull the wires off of the old thermal fuse. My dryer had been not working for 2 months, so I was very pleased that I was able to watch a very detailed video, order the parts on the same website, and receive them very quickly (within couple of days.) My daughter who lives in another state googled my dryer model number with a description of the problem and found your website. She sent me the link of the video to watch as it appeared very easy to understand. She and I both were very impressed by the step-by-step instructions on the video, including a list of all the tools required. I am an 81 year old woman and had no problems fixing this by myself with the assistance of your website. I have recommended this site to several of many friends and family members. Thank you!

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mounted new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him

Disassembled dryer, removed tumbler, replaced drum support rollers

1. Popped off hinged dryer lid at front and supported to allow access to lint chute
2. Removed back sheet metal panel
3. Removed dryer chute to expose sensor; removed same-deformed terminal on top needs to be straightened with pliers to remove through slot.
4. Installed new sensor; terminal needs to be twisted to ensure solid installation and good ground. Bottom pops in but took a bit of finagling.

Accessing and replacing the sensor was straightforward enough; bulk of the job was cleaning off old gasket material (severely degraded) in two locations. Used plastic scraper and razor blade scraper, then cleaned sticky with goo gone. Installed new gasket strip from Home Depot; available in rolls. I used 1/4" x 3/8". Surprising how much lint/hair/debris was in bottom of lint chute. Glad to get it all clean.

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job