LSE7804AGE Maytag Washer Dryer Combo - Instructions

I took out the old lint filter...and slipped the new one in. Pefect fit.

Firstly, remove ac power from washer!
After removing the front panel of the washer (two philips screws), I loosened and removed the plastic motor cover and removed three hex head screws holding the motor. Have someone help you tilt the washer so you can remove the belts by "rolling" them off of the pullies (pump pully and motor pully). What I did was use a chemical degreaser to clean the motor base metal channel where the nylon sliders reside. After doing that and letting it dry, I removed the two old
springs. I ended up reinstalling the old springs because they were not stretched and I installed a new spring (total three) on the right side of the mount. A stiff metal rod with a hook on the end will help you install the springs. Squirt some of the included silicone lubricant on both sides of the motor mount channel and exercise the lube. Reinstall the motor and plastic cover over top of motor. Clean hands and clean belts while you have them out, reinstall belts and front cover and you're finished. My wife said it never ran better!

After removing more bolts and screws than I needed to, here's how to replace the blower wheel on the stacked washer/dryer Maytag SG1000.

Turn off the power.

Remove the two screws on the access panel, which is the canted panel just below the dryer door, and remove the panel.

Remove the two screws at the top of the dryer door. These screws are on top of the dryer facing downward, and unless you're Yao Ming, you won't see them without a stepstool. You can then lift up the door and swing it out from the bottom.

There are two wires attached to the door which you should disconnect. You can set the door aside without disconnecting any other wires.

Next, remove the lint filter and the housing assembly it fits into. First, disconnect the ground wire connected to the upper-left corner of the housing, then remove 4 hex-screws accessed from inside the dryer tumbler.

You should take this opportunity to thoroughly remove lint from inside the housing.

The blower housing is now accessible. Remove the screws on the periphery of the blower housing cover (a.k.a. faceplate), and remove the cover.

The blower wheel is held in place by an external retaining ring and by a blower clamp. The replacement blower wheel came with a new blower clamp, and that clamp can be manipulated with a regular pair of pliers. I went out and bought a pair of snap ring pliers to deal with the retaining ring.

After removing the retaining ring and then taking off the blower clamp, I removed the old wheel. The new wheel was a little tough to put on, but after reading the story of the people who used a hammer to break their wheel, I just pushed on it until it popped on. I used my pliers to install the new clamp, then re-installed the retaining ring and the blower housing cover.

Reinstall the lint duct housing, making sure housing duct centers into the blower seal (looks like a felt circle). Reconnect the ground wire.

While you're inside the tumbler, at the front end of the tumbler just below the door there is a black plastic sensor with two metal bars on it called an automatic dry sensor. Fabric softener can coat the metal bars and cause the sensor to not function. Lightly sand the metal bars to remove any buildup.

Reconnect the wires to the dryer door. Reinstall the door by tilting the bottom in first, guiding the clips on the bottom of the door into the slots they fit in, then push the top of the door into position. Reinstall the screws at the top.

Reinstall the access door.

Turn the power back on! Done!

First I removed the screws that held the side panels on at the bottom, then I removed the screws that held the front panel on and removed the panel. I removed the agitator, loosened the retaining nut with a hammer and a punch, removed the bolts holding the tub springs, removed the bolts for the top panel and flipped it out of the way. Then I removed the clamp for the inner tub and pulled it out, then I pulled the outer tub out. Then I removed the seal and scrubbed the rust off the seal mating area, then installed the new seal and re-assembled the washer. It works perfectly now and no longer leaks and it is over 20 years old. This is the first bit of problem we have had out of this machine, the lonely Maytag repairman commercials are true.

I loosened three screws to relieve the belt tension and removed the belt from the pump drive pulley. After removing the water from the wash tub I removed the intake and output hoses from the pump. I next removed the mounting screws and removed the pump. I attached the new pump loosely and re-attached the belt. I moved the pump to tighten the belt tension and tightened the mounting screws. I re-attached the hoses, filled with water, checked for leaks and replaced the front panel.

This was a pretty simple repair. In this case, the part purchased here was not the actual problem, but had to be disturbed to fix another problem. After many years, corrosion and exhaustion of grease caused the bushing on the agitator shaft to seize, and the belts to slip. In this model machine, the bushing is accessed by first removing the agitator, which is held on by a single 1/4 inch set screw, and then removing the agitator seal, which is held in by a little spring clip on top of a washer. It's soft rubber, and you will probably need a small screwdriver or pocket knife to pry it out. In this case, the bushing was not too bad, so I was able to clean the hardened grease out and free it up with a little oil, using vise grips to rotate the agitator shaft, until the oil worked in enough.

Since seals don't like to be disturbed and reinstalled, and this one requires some prying to get out, I bought a new seal, even though the old one did not leak when I temporarily reinstalled it. There is a spring inside the seal, and it is packed with grease. The new seal comes with the spring and the grease already in it, so all that is needed is to slip it over the shaft (the top has some print embossed on it, making it easy to remember which is the top), press the washer down on top of it, and replace the spring clip.Slip the agitator back on its shaft and retighten the set screw, and you're back in business.

Run the machine, and check the area where the transmission enters the bottom of the tub. There's a little weep hole there, and if the seal leaks, you'll see water coming out there.

Just placed the new filter in place. Fit fine and works well.

Pryed the front cover off and set it aside. I pulled the top cover off by removing the 1/2" hex screws under the front cover and hinged it back. Removed the agitator set screw with a 1/4" hex nut driver and pulled out the agitator assembly. Had to remove the nut that holds the hub assembly in by using a hammer and punch. There is not much room in the tub so be careful you don't hit the sides. It goes off by turning it clockwise. Then the splash guard comes off and then the inner tub with the top gasket and ring can be lifted out of the washer. The tapered cork covered hub was exposed and it also had to be removed with a hammer and punch clockwise after removing the torx set screw on the side of the hub. The rubber seal was now able to be removed under the hub and on top of the bearing on the outer tub. I had to clean all the accumulated scale off seal and bearing surfaces before putting new parts in (rubber seal, hub assembly, and new locking nut). Everything went back easily. Should be good for another 5-10 years...

1 Disconnect dryer from electrical outlet
2 remove vent pipe
3 Tilt dryer backwards and remove front cover bottom 2 philips screws.
4 remove lint assembly and then the fan blower housing with nut driver.
5 with pliers remove retainer clip from fan
6 remove snap ring with pliers or a flat blade screw driver will also work.
7 remove fan
at the same time I replaced the front glides if you do not want to do this then reinstall in reverse order and job is complete.

for glide replacement
1 remove the 4 screws holding the outer ring to the frame of the dryer.
2 drill out old rivits from the back side and then knock out. be careful to only drill rivit and not into metal frame
3 install new new glides makesure you install in correct direction.
4 install pop rivets with stud end on top side of glide. pushing rivet through glide and into the frame ring.
5 pop rivits and make sure they are secure.
6 reinstall ring making sure seal is around ring correctly
7 reintal 4 screws.
8 follow reassembly of blower and lint housing if you changed the fan. if not then just the lint assembly.

good luck the job is really easy and you will save yourself some money

The repair itself was pretty easy. Though I had figured out what needed to be done on my own while I waited for the belt to arrive via Fed Ex, the belt arrived with instructions that described the plan I had already figured and if I hadn't known what I was doing, the instructions would have been a great help.

STEP ONE, UNPLUG THE UNIT (and/or shut off the gas supply), CAREFULLY. Then, I took the front of the unit off by removing the 2 screws on the front panel near the bottom of the unit and disconnected the wiring that shuts the unit off when the door is opened. Set the front door panel aside. Then I removed the front of the tumbler retainer along with the exhaust duct and lint screen assembly by removing 4 screws that affixed the reatiner frame to the rest of the outer cabinet. Set this aside as well. Remove the entire tumbler unit. Set aside. Remove 4 screws on the back of the unit that hold the tensioner and motor access panel and remove it. Set it aside. At this point, I vacuumed every bit of lint and debris from the snapped belt out of the enitre unit, lubricated/greased all moving parts, cleaned off the friction bearing surfaces, and collected loose change ($1.35).

When the belt arrived, I unwrapped it, and placed the smooth side to the tumbler and rubber banded the slack off to the bottom right side (sort of the 4:30 position as you put the tumbler back into the unit). I carefully jimmied the tumbler back into the unit BEING CAREFUL not to pinch the groved belt between the tumbler and any other parts inside the cabinet. I replaced the tumbler retainer and screwed the 4 bolts back into place. I spun the tumbler over near the tensioner assembly (so I could see the slack through the access panel hole in the back) and removed the rubber band. I threaded the belt through the tensioner and over the drive pulley and rotated the tumbler clockwise to align the drive train of the belt. I plugged the 2 wires back into the switch on the inside of the door panel and then I replaced it on the front of the unit and screwed the 2 screws back in at the bottom front of the panel. I plugged the unit back in and tested opperation. It worked great! I unplugged the unit again (I'm not finished yet). I then replaced the access panel on the back of the unit and screwed the 4 screws back in. I moved the unit back against the wall and plugged it back in. Done! The dryer is less noisey now and more efficient most likely b/c I cleaned all the lint out of the thing! Thanks for the prompt shipment of the belt!! I'll get a few more years out of this dryer before spending $700 on a new one!!! Thanks again!

First I unplugged the dryer! Then unscrewed the two screws at the bottom of the front door. To remove the front door, swing the bottom up about 30 degrees until the two triangular hooks at the top of the door release. Then release the two wires going to the door switch from their harness so as to gain more slack to move the door out of the way. The switch was secured by 2 hex head sheet metal screws1/4inch in diameter. I used a small right angle socket wrench to get these loose. I only had to remove the front screw completely to be able to take the switch out for exchange purposes. Once this was done, reverse the process and plug it in! (BTW, the electrical schematic for this dryer is up under the top console)

Remove top two front cover screws. Disconnect wiring. Set aside front cover - door assembly.

Remove two screws at top of the vertical riser cover to expose entire dryer interior. Remove filter. Remove screws to blower cover plate. Remove 4 screws that fasten front drum guide assembly. Remove drum. remove and replace 2 drum support rollers . Replace one rusted drum roller shaft. Replace both drum rollers and non-metalic washers.

Drill out 4 rivets holding two front drum glides. Replace and rerivet new drum glides.

Pry back slighty the many retention points around the front drum assembly which hold the front drum felt seal. Refit the new front drum felt, pressing the retaining clips back in place with a screwdriver.

Replace tumbler motor belt.

Install Drum. Install front drum retention assembly. Install new blower seal with reassembly of blower cover.

Total time - about 1 hour

From previous experience I suspected the thermal fuse. Turned off the power and removed the front of the dryer by removing the two philips head screws in the door hinge and the two screws on the opposite side of the opening. The front came off easily since all that holds it in place besides the 4 screws are two spring clips. The thermal fuse is located on the side of the chamber enclosing the heating element. I removed the wires connected to the thermal fuse and temporarily joined them together with a spade type connector in order to determine if the thermal fuse was the problem. Turned the power back on and tried the dryer......it ran normally. Turned the power back off and removed the thermal fuse by taking out th two screws with a 1/4" nutdriver.
Ordered a replacement thermal fuse, installed it (with power turned off) and put everything back together. Dryer functioned normally after the thermal fuse had been replaced.
The thermal fuse can be removed and reinstalled using a 1/4" nutdriver. The wires are connected with push on spade type terminals.
Note: The swing damper on the dryer vent (the hooded cover where it exhausts to the outdoors) was jammed in the closed position with an accumulation of lint, which caused the dryer to overheat and blow the thermal fuse. If you experience a blown thermal fuse, always look for the cause or you'll blow the replacement within minutes of running the fryer again.

1. Unplug power to the washer.
2. Remove 2 screws from bottom front panel on either side. Panel then rotates out and unhooks at the top. Remove front panel
3. Remove bolts from underneath the top front on both sides using a socket.
4. Rotate the top upward to provide space to see and work.
5. From the back of the washer, remove 4 bolts using a socket around the drain tube at the upper left.
6. From the front, the siphon valve can be removed from the inside upper right.
7. From the front, unscrew the clamp holding the drain hose on the water pump housing at the bottom right front and remove the hose. Be prepared for water to drain from the hose. Remove hose and siphon valve together and discard.
8. Install new hose on new siphon valve and screw new clamp tight. Make sure the rubber ring is inserted properly on the new valve (See old valve for reference)
9. Holding the siphon valve in place, use a socket and re-attach the 4 bolts around the drain tube at the back of the washer.
10. From the front, insert the opposite end of the new hose to the water pump at the lower right front and screw the circle clamp tight. Note: Re-use existing clamp.
11. Rotate the top back down into normal position.
12. Plug the power back in and run a short cycle and watch for leaks.
13. If no leaks, re-attach bolts for the top with a socket.
14. Re-attach front panel with 2 screws. Done.

I was told that it might be a clog in the tube.. we check the tubes that wasn't it Then I Google it and was told it might be the drain pump. I was just glad that Part Select had what I need because my machine is over 20 years old. We change the pump and now I hope I get at least another 20 years out of my machine. I will always use part select to get my parts. Thanks