MLE2000AYW Maytag Washer Dryer Combo - Instructions

Followed the inclose instructions that came with the Motor and Control Board Conversion Kit very easy.

Just put the new one in. I also would like to tell you that I was VERY PLEASED with the service I received from your company. The part arrived very fast. Thank you very much. I will use your service again and will recommend you to others.

Apparently the only way to solve the notorious mold problem on the rubber gasket of the Maytag Neptune front-loading washer is by replacing the door gasket. I ordered the boot kit from you and my husband attempted to do the job without the benefit of an instruction sheet, but I was finally forced to download the repair manual from the Maytag website. Using a screwdriver to remove the the front door, the detergent dispenser, and the shroud, he was able to remove the old gasket, though stretching the spring that held the gasket in place required some strength. The only tricky part was stretching the spring again that holds the replacement gasket in place. With a little ingenuity, a screwdriver (and some dishwashing liquid to make the task a little easier) he finally accomplished it. It took him over 3 hours, but the job is done and the washer seems to be working fine. Your service was fast and efficient and I wouldn't hesitate using your service again, but enclosing a detailed instruction sheet would have been helpful. Now that he knows how to do the job he acknowledges that the it shouldn't take him more than an hour the next time, should the gasket need replacement again. Meanwhile I am going to try tackling the mold problem by leaving the front door open after wiping out the water that remains on the door gasket after each wash.

I used my screw driver to pry the old female end of the latch from the dryer unit. I forced the new female part of the latch into the hole and bang...45 seconds later the door closed securely --like new!

purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in..

no repair needed but the part could not be found in the area i live . ordering was easy and deliver time quoted was very resonable but the part came the very next time that was wonderful.

took the front off by removing two screws took two screws out of element housing undon the wire and romeve element housing then romove the remaing parts that was needed on the new element then reinstall the element housing whith the new element in ti reinstall front of dryer and starting drying clothes project was complete

Very easy with a tip from the video that was provided from Parts Select.
Thank You
Joseph Errico

After checking power to the outlet, I removed the back panel to remove the Control Panel. Testing the timer shoed I had nothing leaving the timer (Door was closed and I held the Push/Start button at the same time. Ordered and replace new timer - still didn't work. Teseted the door button and found it corroded. Tried cleaning contacts and got it to work for a split second. Ordered Door Switch and Push/Start Button -just in case. Replaced door switch - dryer works fine!

Removed the Rear and Front Skins of the Washer. Removed the Belt and Tub Drive Wheel from the rear of the Tub. Removed the Front Rubber Gasket and Bracket Assy. Removed the Tub Cover w/Seal, Spinner Balance Ring (both were damaged.) Knocked the Spin Tub forward with a sharp hammer-rap on the Axle (the Axle is pressed into a Bearing that remains in the Stationery Tub.) Removed the Spinner Assy--found one of the securing bolts on the tri-Arm Support sheared off causing an imbalance. Also, the tri-Arm Support was cracked in various places. Replaced all bad parts using the Spinner Support Assy Kit and new Plastic Washers. Replaced everything else in reverse order then tested. Finally, reinstalled all Machine Skins. Very successful, about 3 hours.

My repair (replacement of Maytag Neptune front load washing machine tub bearings) went well — knock on wood. The reason I took on the job somewhat confidently is I read online (probably from your site) the testimonial of someone who successfully did the same repair I faced. It is this persons sharing the recount of what it takes to do this job that gave me the motivation to take it on. For me it was around an eight hour job being my Neptune is a stackable (with the drier ontop). It has been a week now of operation with about 10 loads through the washing machine. It is sooo nice not listening to the previous worn bearing sound best described as a jet plane winding-up during taking off coming from the washer during its spin cycle. I pray the shaft seals stay snug. The job definitely was a major undertaking. Replacing the seal and bearing myself I saved probably saved $900.
Scott

Opened the back panel of the washing machine. Removed the old belt and wrote down the part number. Shopped online for a suitable replacement and found a perfect match at part select.com. I put in an order and it was delivered in a couple of days! I opened the back panel of the washing machinie again. This time I decided to also replace the isolators that came with the kit. For this, I had to unscrew the motor and gently tug it free. I placed it on the floor of the washing machine. I then replaced the 2 isolators as described in the kit, reinstalled the motor and put the screw back on. I then proceeded to place the belt on the motor and on to the wheel. This took couple of tries to get the grooves right. I then tested the washing machine on a rinse cycle and things looked good. Its been working fine so far.

use an online repair manual for your model, but in the manual it states that the tub bearings are not replaceable, if you are a skilled person capable and competent with fixing mechanical things you should be able to replace the bearings, don't forget to put in a new seal. the bearings can be found at grainger.com , have the old ones in hand for proper size as these bearings are only sold by dimension. This repair will take some time and patience.

I put the new one in . Nothing to it.

I removed front cover of dryer and found heating unit. I needed the detailed drawings from the PartSelect web site to help me find how to get the front cover off. It was easy after that changing out the sensors and reinstalling the heating unit.