110C92962200 Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sherry from TUJUNGA, CA
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Clothes taking too long to dry.
The dryer was igniting when initially starting load, but didn't light again the rest of the cycle. On my model the access was through the front panel, didn't even have to pull dryer out. Open the door and there are two screws on each side.of the inside of frame. Remove screws and lift door off the the whole front of the pulls out and down and removes, and everything is right there to work on. Replaced thermostat, that took 5 min. But didn't fix the problem. So I purchased and replaced the "M" Series New Style Coil Kit, took about 10 min. I took olm/continuity readings b/t all terminals of the old and new coils and they were only about 5% difference, the old being a little lower. But that fixed the problem, works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from St. Louis, MO
- Parts Used:
- WPW10512946
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from SIMI VALLEY, CA
- Parts Used:
- WP3387134
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Pushing start button made buzzing sound but dryer didn't start.
The repair video provided for this model 110.97584810 gave erroneous info. It says to remove the back vent cover. The back on this model is not removable. I wasted an hour trying to remove back and top of dryer before discovering that the bottom front panel below the door pops off. Then the cover of the blower must be removed by removing two screws. The thermostat part can then be accessed and replaced as shown in the video. You'll need a 1/4" rachet to remove the screws as there isn't space to use a nut driver. Note that the statement in the video "This repair is done all from the back" is completely wrong. It is done entirely from the front. It can be done without even moving the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William C. from BIRMINGHAM, AL
- Parts Used:
- 279769
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer wasn't heating
Unplugged dryer, removed back panel, checked thermostats & heating coil with ohm meter, found one stat with broken terminal and one that was bad. Ordered them from this site. Received them in record time, did the installation and was back in business drying clothes. Thanks for video & great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from LAKE FOREST, CA
- Parts Used:
- WP3387134
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Heat stopped after a few minutes
Read this site and saw many fixed the problem with a new thermostat. Ordered one and it was simple to replace. Just removed the back panel of the dryer and the thermostat is right there. Two screws to remove it, swap the four wiring plugs onto the new one, reinstall it. Unfortunately that didn't fix it so went back online and ordered the coil kit, another common solution. Removed front of dryer by removing the two screws the hold the lint trap onto the top and the two hinge plate screws on back of dryer to tilt the top up ward and backward. Removed two mounting screws on inside of dryer front and slip front panel upward to remove. The coils are right in the front down at the bottom left of dryer.Used an offset screwdriver to remove the two screws holding them in place. They slide right out, one has two prongs, one has three. Replace them with the new coils and put them back in place. Reassembled and everything works now. Grand total of eight screws removed and replaced, pretty simple. I'd recommend buying two or three parts if you see several parts as possibilities for a repair. Easier than doing it the dummy way like I did!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from DAYTON, TX
- Parts Used:
- 279769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
No Heat
Removed back cover and replaced thermal cutoff, installed new push on terminals. Bolted back on and dryer is working like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from COLLIERVILLE, TN
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Gas dryer would heat but shut off as it warmed up.
Removed the back panel of the dryer. Thermostat is located in the out going air flow near the exhaust. Removed one screw that held thermostat. Exchanged wires and put everything back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from BEVERLY HILLS, FL
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
dryer overheat
Replaced thermostat on back of dryer, very easy to do, took about 15 minutes after watching video . doe's not require rocket scientist to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from waukesha, WI
- Parts Used:
- WP3387134
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
dryer would heat up once on a full hour cycle
i took a stab that it was the thermostat,but it wasn't.after finding out it was the coils i purchased them and lifted the top of the dryer and undid two screws in the upper front of the dryer and lifted the front off all while holding the tub in place.The coils are located in the very front left of the dryer,i took the holder bracket off,disconnected the wires and replaced the coils(they just sit on a rod)dryer works like new and thanks to the new thermostat also gets hotter,i'm guessing that was next.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from cuba, MO
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
dryer not getting clothes dry
removed door and front panel this exposed all the control devices I changed out the thermostat ndn repaired the dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from HARRISBURG, PA
- Parts Used:
- 279769
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
No heat in dryer
I replaced the thermal cut-off kit. To do this I removed the heating coil assembly. After carefully inspection of the coil I determined it may not need to be replaced so I had this out then replaced the thermal cut off and put everything back. The dryer has been working for two weeks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Canfield, OH
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
dryer door won't stay shut
I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from SAN DIEGO, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch was broke
just followed the video directions, worked perfectly thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from HUDSON, MA
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
I followed your short video and found it very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from ENDICOTT, NY
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken door catch
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this instruction helpful to you?
Thank you for voting!