110C92962200 Kenmore Washer Dryer Combo - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arthur from OXFORD, CT
- Parts Used:
- 279769
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
The dryer would not heat up.
Tested the two thermostats, thermal fuse and the hi limit cut off for conductivity. The hi limit tested open. The others tested closed. Replaced the hi limit. Cleaned lint from the lint duct assembly after removing the two hex head screws that hold the assembly to the blower housing. The lint was packed in there solid. Cleaned up all around. Reassembled everything. Looks and works like brand new. Access was completely from the front panel. CAUTION: The rear panel is spot welded on although it has eight or nine hex head screws also, and when you remove them, the holes don't line up for replacing them. Took a lot of head scratching and time to get things lined up so the screws would go back in again. Don't try to remove the rear panel like the video shows.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Sharon, TN
- Parts Used:
- 285664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
hose split
Pulled washer out from wall removed clamp and old drain hose addnew hose replaced clamp put washer back in plact connected drain to outlet simple operation
Was this instruction helpful to you?
Thank you for voting!
Clothes took way too long to dry (1-3 hours)
The first thing I did was google "whirlpool dryer repair drying takes too long" to determine all of the possible parts I needed to order (the result was 3 possible parts, a heating element and two different thermostats). I then went to www.partselect.com (I'm a repeat customer) and searched the parts using the dryer model number listed just inside the door. I then printed the dryer model diagram off of the www.partselect.com website to determine the location of all the parts and how to replace them. Our first purchase was the new heating element from the www.partselect.com website, received it in just a couple of days and replaced it, but that did not fix the problem. We then ordered the two thermostats, again received them in 2-3 days, replaced them, and were drying clothes in <30 min. in no time! All we had to do was unplug the dryer, disconnect the vent hose, take the back off, unscrew each thermostat, disconnect the wires, install the new thermostats, reconnect the wires, screw the thermostats back in place, replace the back cover, reconnect the vent hose and plug the dryer back in. It took <15 min. for the complete repair! Thanks, www.partselect.com! I will continue to be a repeat customer!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Clements,, MD
- Parts Used:
- 279769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Dryer blew cold air
After removing the exhaust pipe and clamp, I unscrewed the back panel with a 1/4 inch drive socket set. That exposed the wires and the wiring skematic. I used a multimeter to track the power to the element and found that no power was reaching the element. I then unplogged the unit removing all power and tested the resistance on each thermal fuse. The lower fuse had no resistance and the upper fuse did. I then disconnected the upper fuse, used a jumper wire the connect both wires together to bi-passed the fuse. I reconnected the power and turned on the dryer. The dryer element worked, confirming my suspicions of the bad fuse. Once I ordered the fuse and only paid for regular delivery I had the fuse with 24 hours and dryer back together within very little time. It took me more time to clean up the lint dust then it did to fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from KILLEEN, TX
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
door would stay closed
just replaced parys
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Martinez, CA
- Parts Used:
- WP3390291
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
No Heat
Opened up back. Cleaned out lint. Turned on. Heater element went off after 1 minute. I shorted out heat sensor and heat element and stayed on. Got new part and works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALPHONSO from WASHINGTON, DC
- Parts Used:
- WP3390291
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer no heat
Repair was easy but still no heat to dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from GRAFTON, IL
- Parts Used:
- WP3387134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Clothes never completely dry
I watched the video then called them to order parts. They were VERY helpful & NICE. I had the parts the NEXT day. I followed the video instructions & it worked. They made my day! THANK YOU JoAnn & Teresa!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindie from DUNMORE, PA
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable), Wrench set
Front legs were rotted.
Replace front legs. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sheldon from macon, GA
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
dryer want heat up
they sent the wrong part . when i got the right part i removed the two screws holding the element . took the Thermostat out . removed the plugs . put the new thermostat in plug in the plugs. screwed the element back in place . And now i need to replace the fuse located at the top of the element casing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobb from SANTA BARBARA, CA
- Parts Used:
- 285664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rats chewed through hose.
New hose was perfect, went on easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from SEVERNA PARK, MD
- Parts Used:
- WP358594
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
plastic cover came off rear leveling leg
slipped new rear leveling legs into leveling fixture. Fit even though it wasn't specified to be the right part for this old washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from WIMAUMA, FL
- Parts Used:
- W11086603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken grill
With the instructional video the repair was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from WOODLAND HLS, CA
- Parts Used:
- WP3387134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer wasn't getting real hot and took a few cycles to dry.
Thank goodness the part was still available for a 25 year old dryer. Website was great to help solve the problem and the video was wonderful to show me how to identify the part and how to get to it. You take off the back of the dryer and then unscrew the thermostat from it's mooring. Undo the 4 wire connections. Stick in the new thermostat and re-install. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melody from TEXARKANA, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer door wouldn't catch and stay shut
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this instruction helpful to you?
Thank you for voting!