Models > 110C92962200 > Instructions

110C92962200 Kenmore Washer Dryer Combo - Instructions

Jump to:

All Instructions for the 110C92962200
76 - 90 of 374
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Amy from JUNCTION, TX
Parts Used:
WP22002263
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bulb worked for a couple days and has now burned out, filaments dangling
To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shelly from Flagstaff, AZ
Parts Used:
279769
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set
First taking too long to dry, then no heat at all.
Unplug the machine. Take off back panel and remove heater assembly. Since I was already into the heating system, I replaced the heating element as well ($30). I replaced the old thermal cut off and overtemp, put the wires back on the connectors, reassembled, and the dryer works like it did when brand new! Within 30 minutes the repair was completed. Still saving for a new front loader washer/dryer, so the repair will hold us until we have enough to buy new. Alos, helped us to need to dry clothes on a clothes rack in the house. Good practice and lesson for the entire family!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RICHARD E from UNALASKA, AK
Parts Used:
279769
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
gas flame would shut off after + or - two minutes
the igniter worked so replaced the two coils on the burner, did not help, read the diagram that came with the machine and replace the high limit cut out. that did it, however the mounting bracket needed to be modified by grinding a tab off, so that the cut off switch would fit in to the bracket.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from WICHITA, KS
Parts Used:
WPW10314173
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
Loud squeaking noise
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DAVID from DANVILLE, VA
Parts Used:
279769
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
no heat
unplug the dryer used nut drive to take the back off unhook the hose from dryer . disconnect the wires. remove the 2 screws from thermal cut -off . install the new parts
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from ROCHESTER, MN
Parts Used:
279769
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Dryer would not heat
Remove the back panel. Remove wires from top sensor and bottom sensor and remove old sensors. Install new sensors and replace wires. Dryer works great.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from DURHAM, NC
Parts Used:
279769
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Dryer wouldn't heat
Replaced Thermal Cut-off kit and Heating Element
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Samuel from PICKENS, WV
Parts Used:
279769
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
Dryer would not heat up.
Watched video and removed lower cover of dryer then removed and replaced the thermal cut-off .Dryer works great now.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frederick from NORTHWOOD, NH
Parts Used:
WP3387134
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Low or no heat
Ignor installation video. it is for a different model dryer. The part is not accessed from rear. It is accessed from the front panel. Disconnect power. Remove two screws below front panel with cross head screwdriver. Swing panel up until it releases. No need to disconnect wires just put front panel down beside the dryer. Thermostat located right in front on duct easy to identify since it has four leads. Remove wires with needle nose pliers. Remove thermostat with nut driver. Contacts are labeled but hard to read. Hold thermostat so the lead number 3 (the 3 will be upside down) is on the left. Connect blue wire. White wire to top. Purple wires to bottom and right. Reverse removal procedure and you are done.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lawrence from GOLDENDALE, WA
Parts Used:
279769
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set
Dryer rotates but there is no hot air.
Our dryer produced no heat. I thought that it was the electrical heating element because this part had failed a number of years ago. But when we received the heating element, and I opened up the back of the dryer to install it, I found that the element was OK. (Visual inspection as well as using an ohm meter.) I then ordered the thermal cut-off kit, (which was over a week in getting to us because Fed-Ex misdirected the shipment). Once the kit arrived it was very simple to remove the Allen-head screws on both parts, install the two new parts, reconnect the wires, replace the back panel on the dryer and hook up power and the dryer vent hose. The dryer works just fine.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carl from MARION, KY
Parts Used:
WPW10359272
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sean from ROCK HILL, SC
Parts Used:
W11086603, WP3387230
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Part broken in half
Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from WARREN, NJ
Parts Used:
279570
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dryer door latch broke and door wouldn’t stay shut.
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Virginia from SNELLVILLE, GA
Parts Used:
285664
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Old drainage hose had a break in it.
Removed broken hose and replaced with new hose. My washer will be 21 years old in January.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from BIRMINGHAM, AL
Parts Used:
285664
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Old outgoing water hose leaking
1. Need mop, bucket to catch leftover water in machine before you remove old hose. 2. Removed old hose by removing clamp. 3. Dried up any remaining water around fixture before attaching new hose. 4. Slide clamp to bottom of hose before attaching to machine. 5. Attached hose and clamp to machine where old hose was removed from. Make sure clamp is secure. (Please note that clamp that came with the new hose was too big. I used the old one. Worked perfectly). 6. Finally run a little water in you washer, then run out to test tightness and there is no leaks.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 110C92962200
76 - 90 of 374