CRE7600ADL Maytag Wall Oven - Instructions

My wife detected the problem Wednesday evening before Thanksgiving. We've had the heating element break before, so we knew right away what the problem was. We ordered the part that night, and even though we weren't able to cook Tom for Thanksgiving, the part shipped on Friday and arrived the next Thursday.

First, I turned off the power to the stove at the circuit breaker.

Then, I removed the two screws that hold the element in place. They are on the top of the flange and partially concealed by the convection element that juts out.

I pulled out the heating element, disconnected the electrical leads, and installed the new one.

I attempted to put the screws back in, but they were a little tough to line up. I decided to leave them out, knowing that I will probably be doing this repair again in a couple of years.

Hopefully, next time it won't be the day before Thanksgiving.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

Rehooked up wires on new element, Slid the element in place. Replaced the two screws. Done, very easy.

My husband removed the screws holding the damaged element and removed it before the new one arrived. When we received the replacement part, it took only about 10 minutes for him to repair the oven, inserting the new element.

First I removed the two screws that hold the element in place. I then pulled the element out about three inches and disconnected the two wires, being careful not to pull the plugs off. I then inserted the new element and reattached holders. It was very easy and took less than five minutes. The part arrived amazingly quickly. The stove works great now.

the new elements were super easy to replace. the old ones just pulled out and the new ones easily pushed in. the top one was a little more difficult only because it had brackets that had to be slid of and then slid onto the new one.

Called repairman, he never called back for a week. Gave up and found your website, ordered the part. You said it would take 3-5 business days. You lied, it was there the next day. Taking old element out starts with shutting off the juice. Remove trays, pans, etc. Unscrew two screws, pull out elements ends, unclip from wires, reverse the process with new one. You need a light to do this.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires reverse the order to install the socet was easy but after i was done discovered that the base of the old bulb was stuck in the socet keeped it for future use

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Turned off the breaker to the stove. Removed the screws holding the old parts in and unplugged the element. After reshaping the element because it got damaged in shipping I plugged the wires to the new element, replaced the screws and turned the breaker back on. Tried the stove and it has worked fine since.

Unscrewed 2 holding brackets. Removed old element. Unfortunately one clip broke off the wire and had to be replaced. Attached clips to element and replaced holding brackets.
Job is simple but working in the oven without damaging the oven door requires a younger back.
Without problems should take ten minutes.

Removed two screws and unpluged old element plugged in new element and re-attacheched to oven. No Problems at all.

Removed 2 screws, should have tripped breaker first but learned the hard way, unplug wires, install new.

Repair is really easy. Just remove two screws, pull ( gently ) on the bake element until you see the electrical connectors. Remove and do the reverse with the new part. Oven works just fine.
Really Really easy....

Removed old coil by unscrewing the element and unplugging it from the wires, adjusted the terminal slightly and plugged in the wire from the new element.

It was a very simple process and would have taken me less time if I wasn't so old and couldn't bend easily!

Repair went fine as I read on how to do it and it worked fine. Hardest part was hitting the hole for the screws.