CWE5800ACB Maytag Wall Oven - Instructions

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

This was an easy thing to do. Take the two screws off the back, pull the wires out, pull off the connectors, get the new element, replace the connectors, make a hole in the insulation, fish the wires back behind the insulation, screw the mounting screws and turn it on. The only thing I did extra is clean the bottom of the oven because with the element out, it's easy to do.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Connected the wires to new element, pushed wires back into the back wall, re-installed screws.

Found the model number, called the local parts store, they quoted $60 + $10 shipping because it was a warehouse order or something. So I came hear and got it for $42 + $7 shipping!

Turned off power, unscrewed the element, disconnected the clips from broken element, connected them to the new, screwed in the new element, and it was done

Determining the correct bake element to order was the most difficult part. Once I received the part, it took me 2 minutes to unscrew the back panel, detach the wires, connect the new wires and re-connect the back pannel - turned the oven on to test - and we were all set just in time for Chistmas baking.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Went online and Googled for oven element by providing the serial and model number. Partselect popped up. I submitted the order and received and installed the new element within 5 days from start to finish. I recommend this website for replacement parts.

Awesome, just awesome, you guys are great and I will use you again and again.

Pulled the old one out and installed the new one

I took out the old part and we went on line and found everything from your PartSelect and ordered it. The part worked great and we received the part in two days. Thanks so much, you saved us lots of money and the oven works wonderful. I have told many people about your company and how much we like the help from you. Paul from Quincy, IL

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

The part arrived promptly and as described. I had already unscrewed the bad coil so it was easy to just put the new one back in on the open sockets. I then put the top support plate through the element and quickly screwed it back on.

Removed old element and element gasket. Replaced both by alining gasket with element and screwing in retaining screws. Jod completed.

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.