Models > W2780W > Instructions

W2780W Jenn-Air Wall Oven - Instructions

Jump to:

All Instructions for the W2780W
106 - 120 of 149
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Cindy from Polson, MT
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Had code F1 and F3 on my oven. Oven wouldn't heat.
Watched the video and it was as easy as described. Not many things go as easily as this.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Agusta, GA
Parts Used:
WPY04100020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Baking Element burned out
Removed racks from oven, unscrewed two screws holding old element in place with philips head screw driver from the back wall of oven. Carefully pulled element from oven to expose connecting wires and then pulled two wires loose from old element. Reconnected wires on new element and carefully reinstalled element to rear of oven interior with two screws removed from original element.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Max from Bothell, WA
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The oven was not heating up to temperature
I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electronic clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from Acworth, GA
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
My oven was not holding temperature.
I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sreve from Deland, FL
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven would not program and would shut down
The "PartsSelect" General discription of the parts funtion helped me to confirm my suspitions that there was some form of temperature registering problem. I whatched the short video they provided on how to change the part out, even though, in this case, it's pretty self explanitory.The part was in my hands a day erlier than promised and in reality, much earlier than I had anticipated from the beginng. It took me all total, 20 minutes to exchange the part out and have the oven in operation again.
Was this instruction helpful to you?
Thank you for voting!
Customer:
kathy from charlotte, NC
Parts Used:
WPY04100020, WP7101P126-60, 8009
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
the oven did not heat, the lightbulb was burned out and there was a screw missing on the door frame.
I read the online instructions sent in by previous diy'ers. the repairs, esp. the heating element replacement went just as described and went really well. I have used the oven and it works beautifully. Total cost of parts was a little over $60.00. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Dacula, GA
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Fan runs continually ,door locked,error code f2,f3,f7
Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lynn from Crest Hill, IL
Parts Used:
WPY04100020
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
element had caught on fire
Removed the screws from the back of the oven to remove the damaged element; removed the electrical connectors and reattached to the new element and screwed it back in
Was this instruction helpful to you?
Thank you for voting!
Customer:
DAVID from Cape Coral, FL
Parts Used:
12001656
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
When We Turned On The Oven The Temp. Reading Went Up To 425 And Beeped By No Heat
Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from homilton, MT
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven randomly turned off and locked
Replace the oven sensor per the excelent easy video you provided
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from San Jose, CA
Parts Used:
12001656
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
F-4 Code, oven wouldn't heat
Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding the wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Betty from Riva, MD
Parts Used:
WPY04100020
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Rupture of bake element through coating causing flaming and sparks in oven.
We removed the 2 screws at back of oven that hold element on, which took some doing as they were very rusted. We then pulled old element out; this proved a bit difficult because the ends of the old element were stuck in the insulation behind. We had to wiggle the old element back and forth a bit to get it loose from the insulation. Other than that, it was easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
tom from winter haven, FL
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
temperature varied in oven.couldn't set
removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair
Was this instruction helpful to you?
Thank you for voting!
Customer:
Phillis from Alburn, CA
Parts Used:
WPY04100020
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Oven lower element shorted out
In my 26 year old oven the screws to remove the element were extremely difficult to remove, but with 6-10 applications of Liquid Wrench and brute strength we finally did. We were a bit concerned with the insulation that was protruding but used electrical tape to secure the wires to the leads for good measure. All was successfull. I love my Jenn-Aire double oven!
Was this instruction helpful to you?
Thank you for voting!
Customer:
MARK from roseville, MN
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven would overheat
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the W2780W
106 - 120 of 149