Models > W2780W > Instructions

W2780W Jenn-Air Wall Oven - Instructions

Jump to:

All Instructions for the W2780W
91 - 105 of 149
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Dennis from Tampa, FL
Parts Used:
12001656
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
F1 Fault Code - Replace the Temperature Sensor
The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.
Was this instruction helpful to you?
Thank you for voting!
Customer:
peter from springfield, PA
Parts Used:
WPY04100514
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Failed Broiler element
Removed back of stove - 4 screws on top, 3 underneath. Unplugged wires from element. Removed element - 2 screws in front and 2 in the back. Installed new element, plugged wires back in, reinstalled back panel.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Claude from Lakewood, OH
Parts Used:
12001656
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Oven would not heat
Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wayne from Grantsburg, WI
Parts Used:
12001656
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Temp spikes.
Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JAMES from SEATTLE, WA
Parts Used:
12001656
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Long Oven Sensor failure - oven over heated & shut down
Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Cumberland, MD
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
oven not staying on. fault cod F-3 showing
Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alan from Bonita, CA
Parts Used:
12001656
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Top oven sensor
The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anne Marie from Huntingdon Valley, PA
Parts Used:
12001656
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
oven temperature only goes to 275 degrees even when set higher; broiler works
I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff from Thousand Oaks, CA
Parts Used:
12001656
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Oven would not heat on Back Cycle
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lloyd from Eau Claire, WI
Parts Used:
12001656
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
change oven sensor
Followed provided video
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jill from South Lyon, MI
Parts Used:
WPY04100020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
oven heating element
The heating element in our old old oven broke in half. Luckily we were able to find a replacement part (which we didn't think we would that's how old the oven is)! The part arrived within a couple of days, my husband removed the old element (toughest part was getting the two old screws unscrewed) plugged in the new one and he was done. Took about 5 minutes! I turned on the over to test it was connect properly and it started heating up right away! We are VERY happy !! :o)
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from Saint Louis, MO
Parts Used:
WPY04100020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replace lower internal coil in over
Remove screws, remove old coil, place new coil, screw back in. The hardest part of this task is removing the existing screws which are most likely partially corroded and hard to move.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marylou from NORTH BENNINGTON, VT
Parts Used:
Y704660
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
no problem just wanted new oven racks
take the old ones out and slide the new ones in ordered around 2 in the afternoon and they were delivered to my front door around the same time the next day very pleased with service and the racks. I just wish I could get parts for my Jenn-Air cooktop which is 20 years old maybe somewhere someday.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DEBORA from YELM, WA
Parts Used:
WPY04100020
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The element burned up.
My husband removed the old element and replaced it with the new one. I think he used a screw driver to remove and replace. The part shipped and arrive in 5 days. Quick and easy!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barry from Wildwood, MO
Parts Used:
WPY04100020
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Burned out bake element
The most difficult part of the repair was removing the two Phillips screws that attached the element to the back wall of the oven. With some WD40, and a hammer to tap on the screws through the screw driver (and several hours) the screws finally came loose. Once the screws were out it was a matter of removing the two wires connected to the element and reconnecting the wires to the new element. After removing the screws this job took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the W2780W
91 - 105 of 149