W30400P Jenn-Air Wall Oven - Instructions

Turn off breaker to stove. Open oven door and remove screws up under display. Slide display down and tip top edge forward so you can see the back side. Remove 2 screws holding digital display and disconnect 3 wiring plugs. One of them is a ribon connector and you must squeeze it to make the front edge rise up to disconnet the ribbon and again when putting new part in. Reverse the proceedure. It took my husband 10 min to replace the part. Being able to read how others had done it was invaluable.

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

The front panel was removed by unscrewing six screws just above the oven door and then four nuts were removed fron the burner assy. using a nut driver. The circuit board with the clock assy was then available. It was then just a matter of removing three cable connectors and a ribbon cable connector and two screws to remove the old clock assy. The reverse was done to install the new clock assy. The whole operation took about 15 minutes.

I removed the screws that hold the front of the range on, removed the two screws holding the clock assembly, and replaced the old with the new. It was brainlessly easy.

Turned off power to stove
Removed control knobs and retaining screws under the knobs.
Opened oven door.
REmoved screws (4) holding the face plate to the stove.
pulled the panel downwards.
Unscreewed clock circuit board.
Removed connectors (3) (See Below)
NOTE the flat ribbon needs to be removed by pinching the ends of the black connector , liftiing and GENTLY pulling the ribbon out of the connector. The black connector remains on the circuit board.
When in stalling the ribbon, pinch the ends of the black connector and lift slightly, insert ribbon, then push down on the loose side of the connector until it snaps shut ,forming a tight connection.

Reverse steps

I have only two things to add to the other repair stories on this site: (1) Unlike the ribbon cables inside desktop computers, the ribbon cable on this range is entirely separate from the connector, which is permanently attached to the clock assembly. There are clips on the top of the connector at each end. Push them in and raise them gently to release the ribbon cable. (2) There are two Molex connectors attached to the clock assembly. The pins for one of them were bent on the new clock assembly I received. Before installing it, I spent some time gently coaxing those pins back into alignment. Use your fingernail, and be patient.

unscrewed the top face plate assembly disconnect 2 wire harnesses 4 screws to release display clock 1 wire harness and then reverse order

1) Unplug Appliance
2) Remove stove front (4 hex-head screws)
(Note: support front while removing screws)
3) disconnect (3) wiring harnesses
(Note: exercise care when revoving "data bus", release with small "dogs" on each side of plug.)
4) Remove Clock assembly (2 hex-head screws)
5) Replace Clock assembly (2 hex-head screws)
6) Reconnect (3) wiring harnesses (reseat bus plug dogs)
7) Reattach stove front (4 hex-head screws)
8) Plug appliance in to power outlet

Note: Before the repair, all functions and displays worked just fine, they just weren't illuminated so you couldn't read any thing. It really steams me that I had to pay $141 to replace a 50 cent light.

Turn off power to the stove. Pop off the burner knobs and remove the screws attaching the controls to the front panel. Open the oven door and remove the four screws attaching the panel to the oven frame. The panel slides down giving easy access to the circuit board. Remove the two connectors and the ribbon cable attached to the board. There are small clips on the side of the ribbon cable connector that release the ribbon cable. Unscrew the board and install new board. Reattach the cables, put the panel back in place and attach. Reattach the burner controls to the panel, pop the knobs back on, power the stove back on, put on a pair of sunglasses to view the now blazingly bright display and admire your work.

Turned power off to oven, removed control knobs, took out four screws under panel. Removed four 1/4" sheetmetal screws. Removed front cover, Removed two additioanl screws that held front cover to corner bracketts, Removed two screws that held clock to plate, removed each wiring harness and pluged into new part, unplugged wiring ribbon from old part plugged into new. reassembled. Turned power back on and tested and we had light!!!One repair company was going to charge us over $400 to make this repair!!!

Open oven door
Remove two sets of four screws underneath the LED display
Remove stove handles (pull off easily - no tools needed)
Lower flat plate width of oven and about two inches deep should be able to drop out from under the clock display.
Remove face plate over clock.
Unscrew four screws holding clock unit down.
Undo two electric connectors and the thin ribbon connector - the thin ribbon connector is different - the ribbon comes loose and the black plastic connector stays in place on the board.
Press the thin ribbon connector ends inward and pull up to detan ribbon on old one and then to insert ribbon on new one.
Reverse the rest.
Not too bad!

Loosened the contol panel until I was able to get to the Digital Display board.
Removed the three cables and the screws that held the display unit to the control panel.
Reversed the procedure to instll new digital clock display unit.

This is the second clock I have had to put in this unit in about that many years. The first time I disassembled far to many things. This time I knew to only unscrew the front panel and side triangle plates. The process was much faster the second time. I hope this is not a chronic problem though.

My microwave is stacked on this stove. I had to pull cover off to slide part off. screws were a snap. only problem was the slip catches on the ribon strips. Sperating with flat head was scary but worked fine.

piece of cake KILL POWER AT BREAKER BOX. Remove burner knobs exposing 4 screws. Open oven door exposing 4 philips srews, four 1/4 hex head screws, and 2 philps screws for end caps. Had to pull out range about an inch (less) away from countertop. Remove screws. Move end caps away from face plate.Pull out face plate. Pull down / out bottom plate to expose Assembly. Unclip wire connection, carefully pull out ribbon connection. Remove 2 screws. Install in reverse.