W241 Jenn-Air Wall Oven - Instructions

pulled one off and pushed the other one on.fino

Received the part within 10 days and installed in less than 60 seconds.

Remove screws, remove old coil, place new coil, screw back in. The hardest part of this task is removing the existing screws which are most likely partially corroded and hard to move.

The heating element in our old old oven broke in half. Luckily we were able to find a replacement part (which we didn't think we would that's how old the oven is)! The part arrived within a couple of days, my husband removed the old element (toughest part was getting the two old screws unscrewed) plugged in the new one and he was done. Took about 5 minutes! I turned on the over to test it was connect properly and it started heating up right away! We are VERY happy !! :o)

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

Pulled old knobs off and put new ones on. Thanks and god bless! Wanda

The new knobs were simply pressed in placed on the existing shaft, perfect fit, looks just like new, yet 24 years old. Would tell family and friends to shop for parts at Part Select.

Removed racks from oven, unscrewed two screws holding old element in place with philips head screw driver from the back wall of oven. Carefully pulled element from oven to expose connecting wires and then pulled two wires loose from old element. Reconnected wires on new element and carefully reinstalled element to rear of oven interior with two screws removed from original element.

My husband removed the old element and replaced it with the new one. I think he used a screw driver to remove and replace. The part shipped and arrive in 5 days. Quick and easy!

opened the door; put 12 penny nails in each hinge through the holes for it, removed screws above hinges; slid door off; laid it on a towel on the workbench; removed side/top/bottom screws and laid the outer door aside. removed the screws from the inside of the door, laid the inside glass aside, removed the glass assembly (broken), cleaned the loose glass out, laid the new glass assembly in place, replaced the panels and screws and slid the door on the hinges, removed the nails and closed the door. 35 minutes. Never did it before4. Part fit great! Thanks to partselect for having the discontinued part!

Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

Removed the screws from the back of the oven to remove the damaged element; removed the electrical connectors and reattached to the new element and screwed it back in

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

We took the door off, you have to be careful of the hinges popping back. We put small screwdrivers on each side and held the hinges out, this made the door easy to just stand up and slide back on the hinges. The glass replacement was simple just a few screws. We spent $127.00 on the part and shipping and a new wall oven would have cost us $1500.00. Thanks for making this part available.