Models > 2043499990 > Instructions

2043499990 Kenmore Upright Vacuum - Instructions

Jump to:

All Instructions for the 2043499990
106 - 120 of 306
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Francisco from Tacoma, WA
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
water pump leaking
It was as simple as undoing 2 clamps and removing 2 hoses then just perform that in reverse to put the part back on. And in 10 mins i was using the washing machine.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
CEDRIC from SAN DIEGO, CA
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
The water pump developed a leak
First I removed the clamps that holds the pump in place.
Next I removed the water hose clamps.
Then I did the reverse to finish the repair.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Don from Apple Valley, CA
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Water leak
I pulled the machine out about two feet from the wall. No need to disconnect any hoses. Tip up the front, place an automotive jack stand under the front of the machine to hold it approximately a foot and a half up. Lay on the floor, remove the hose clamps, flip the two spring clips off that hold the pump, and it's off in minutes. Place the new pump in position and replace the two spring clips, slide the hoses back on and install the clamps. It couldn't be easier or quicker. Replacing the pump took 5-10 minutes max. The longest part of the project was cleaning up the spilled water..!
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bobby from Centertown, KY
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
washer was leaking water
pulled the washer away from the wall and turned it on its side. I had to remove the gear box and motor to get to the part. Had to remove the whole insides. Install the part and put everything back in.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
jose l from elk grove, CA
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
won't spinn was stuck was thinking the motor or gears was bad guess what was the problem
remove the motor remove hoses find sock inside of pump couldn't removed install new pump take less than 2 hrs to fix
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roy from Olympia, WA
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
small leak - drip every 6 seconds when pump filling or draining washer
First, disconnect from power & turning off the water. Then, tried to access the part by tipping the unit back enough to work. Was able to remove the hoses by loosening the spring clamps.. The pump motor shaft had corroded enough to make removal of the pump almost impossible. The washer had to go full onto its back side; had to pry with on the pump with the crowbar and tap the crowbar to get the pump to slowly move off of the shaft. Once forced off, additional time was spent removing corrosion from the shaft. A little lube was used on the shaft. Re-assembly was quick & washer was righted, plugged in and returned to service. Much better than buying a whole new washer.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Rancho Mirage, CA
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set
There was a leak when trying to wash clothes
Stackable Unit. Removed the front cover between dryer and washer with a phillips screwdriver. Loosened the two bolts securing the top cover of washer. Removed the cover to access the two bolts securing the front panel of the washer. Removed that panel for access. Removed to clips by hand and used pliers to remove hose clamps. Installed new part. Damage was visible on the old part. Good as new.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Biglerville, PA
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Leaking in the front of the washer.
1. turn off water valves going to washer
2. disconnect hoses and electric in back of washer
3. put screwdriver under top control panel and pry
control panel up
4. flip control panel back
5. use screwdriver to pry gold colored clips on right and
left which secure washer housing
6. pull housing forward until completely off washer
7. at this point the partselect website recommended
tilting the washer on it's back but I chose to work
on the pump with the washer upright
8. pull both hose clamps on the two hoses attached to
the pump back and remove the two hoses
9. remove the two metal clamps holding the pump
10. pull the pump directly off it's drive shaft
11. put the new pump on over the drive shaft making
sure the support "legs" of the new pump are in
their support holes.
12. basically work back through these steps to reassemble
the washer
13. The biggest problem I had was getting the housing
back on the washer. I was working by myself and it
was difficult to get the housing to seat properly
on the frame's metal flanges. I eventually got it
on and the washer is working great with NO LEAKS!
14. Piece of advice for getting the housing back on the
washer: Get the front of the housing on the front
of the frame first and then LOWER the housing DOWN
on the metal frame carefully matching the frame's
flanges with the holes in the housing.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James W from Winton, NC
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
washer stopped while full of water
With assistance the washer was walked out the door to the deck where it could be drained.
The machine was examined, and the pump identified. THEN I found this site while looking
for the part. Had I started here, I would have learned that I could service in place by just
tilting it back against the wall! The part was identified, and phone call made to charming
rep and part arrived in a few days. Do be careful to keep track of the latches that clamp
the pump in place, as they can fall out when not clamped down on the pump.
No unusual tools or skills needed. Door clearance and outside temperature were greatest
issue for us, and wasn't even necessary.
As it was, my wife worked diligently to remove the inhaled sock from the pump. We gave up
on that as the #1 complaint on this pump was 'leaking'. Had I started here, repair time
would probably have been less than 30 min hands on time. We spent much more.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Murfreesboro, TN
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Leaking Water Pump
The WEB site is excellent, and I believe has been put together by very experienced repair people.

The Trouble shooting tree is excellent, it went right to the problem.

I would give the whole repair operation an EXCELLENT Rating except for one show stopping omission.

The console on my unit is SCREWED to the TOP REAR of the washer.
This step is missing in the video. The two screws are easy to miss as they are in a recessed area. Also the console is attached to the top with plastic fitting that fit into recessed openings in the top. To make matters worse, using a putty knife to release the spring clips may actually damage the plastic fittings.

It may be that the manual covers this change, but I did not print it out. A possible solution might be to put a warning in the video to inform the repair person to look in the manual for this change.

Over All - A VERY GOOD JOB. I will use it again if needed, and I have sent your URL to several of my friends.

Robert Hopkins, TN
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ron from Laramie, WY
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
The pump was leaking water onto the floor
I unplugged and detached the hoses from the faucets & drain. Then I pulled the washer out from the wall and tipped it onto its back so that I could access the water pump from beneath. I used pliars to compress and move the two hose clamps holding the hoses attached to the pump, then used a screw driver to pry the two retaining clips from the pump. I slipped the pump from the shaft and pulled the hoses from their connection. To install the new pump, I simply reversed this procedure. After installing the new pump I set the washer up and lifted to set it on benches (so that I could inspect the mechanism while running the washer), Then I re-attached the water and electrical and ran the washer through a cycle while watching for leaks. Then I returned the washer to its original position. Overall, it was an easy fix.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bartholomew from Northville, MI
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Leaking water pump
I followed the Partselect Video - it was a very good guide. the only issue i had was the motor shaft was rusted and the new pump could not be installed until i wire brushed the rust off of the shaft and filed the shaft to the proper size. then i installed the pump and reassembled the cabinet and it worked fine.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jim from Temple, TX
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
leaking water on floor
It was real easy!!!! gave part to my maintenance man. he pulled old part off, then put new one on.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
elton from detroit, AL
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
leaking under machine while filling
First disconnect power supply, close both water supply valves, move machine away from wall and tilt machine back so that front of machine was about 12 to 14 inches off the floor. Place bucket under pump and hoses, wrap plastic around electric motor to prevent water from getting in motor. Disconnect hoses allowing water to drain in bucket, remove two retainer clips on pump, and pry pump off motor shaft. Use sandpaper or wire brush to clean rust off shaft, apply a small amount of oil or other lubricant to motor shaft, install pump aligning pump drive to motor drive, install retaining clips and reconnect hoses. let it down, plug it in, and turn on water, then wash.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
kevin from lockhat, TX
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
water leaking
took the washer outside on the back porch and then took it apart. replaced the water pump and everything worked well.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 2043499990
106 - 120 of 306