2043499990 Kenmore Upright Vacuum - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Clifford from Friendship, NY
- Parts Used:
- WP3363394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
water leaked out from under the machine.
I read the trouble shooting guide on your web sight to figure out what the problem was and after checking the hoses the pump seemed the next most likely problem. So I ordered the part.My main problem was the lack of room to work,if I could have tipped it on it's back or raised it I would not of had a problem.But I tipped it up and blocked it from falling and removed the part while waiting for the new one to arrive.Once it arrived it only took a few minutes to install.When I tried the washer it still leaked water,so I tipped it back up to check it out.The only thing that was wrong was that the spring hose clamps had not seated yet so I moved them around and wiggled the hoses to try and get them tighter.The next time ,it worked fine.The other reviews and trouble shooting guide were a great help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Hereford, AZ
- Parts Used:
- WP3363394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Leaking at pump
First of all, it would have been helpful to have two people take the housing off the frame. One to lift and the other to disconnect the hoses that need to come off the pump and the filler.
Second, THANK YOU to another person that posted about prying the pump from the motor and sanding it to accept the new pump. When I couldn't get the pump off the motor due to rust, I thought both the pump and motor were done. But I worked the pump off the motor shaft (I had to break the old pump, but it was toast anyway) and used a wire brush and sandpaper to clean the shaft. When I got the new pump, it slid on like a champ!
I also used the parts list that came with the washer to make sure I got all the parts back together in the right place. Like I said, I took too much apart and didn't pay attention to what I was doing for later reassembly. Even though the parts list that came with the washer is small and not to scale, it helped me put the thing back together.
I got my part when PartSelect promised and I got help here from the website. I will use this company whenever I need an appliance part.
Second, THANK YOU to another person that posted about prying the pump from the motor and sanding it to accept the new pump. When I couldn't get the pump off the motor due to rust, I thought both the pump and motor were done. But I worked the pump off the motor shaft (I had to break the old pump, but it was toast anyway) and used a wire brush and sandpaper to clean the shaft. When I got the new pump, it slid on like a champ!
I also used the parts list that came with the washer to make sure I got all the parts back together in the right place. Like I said, I took too much apart and didn't pay attention to what I was doing for later reassembly. Even though the parts list that came with the washer is small and not to scale, it helped me put the thing back together.
I got my part when PartSelect promised and I got help here from the website. I will use this company whenever I need an appliance part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Meridian, MS
- Parts Used:
- WP3363394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers
Water leak from old pump
I Removed hose clamps and 2 pump clamps. I took the old pump(had a small hole burned in it) off and replaced it with the new pump. I replaced the 2 pump clamps and the hose clamps and it was ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nolasco from San Diego, CA
- Parts Used:
- WP3363394
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Water leaks during the spin (drain) cycle.
Unplugged the washing machine. Removed the two philipps screws holding the control panel. Swung it up , disconnected interlock connector, and pried the two clips. Removed the top and cabinet assembly to have easy access to the leaking pump.
Disconnected the two hoses connected to the pump. Used the plier to loosen the hose clamps. Removed the two retainers securing the pump. Removed the old and damaged pump and replaced with the new one. Reinstalled the retainers back on. Reconnected the hoses and clamps. Put the top and cabinet assembly back on. Snapped back the clips and reconnected the interlock connector. Screwed the control panel assembly to the cabinet. Done. Ran the washing machine to check for leaks. Found none.
Disconnected the two hoses connected to the pump. Used the plier to loosen the hose clamps. Removed the two retainers securing the pump. Removed the old and damaged pump and replaced with the new one. Reinstalled the retainers back on. Reconnected the hoses and clamps. Put the top and cabinet assembly back on. Snapped back the clips and reconnected the interlock connector. Screwed the control panel assembly to the cabinet. Done. Ran the washing machine to check for leaks. Found none.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Fort Madison, IA
- Parts Used:
- WPW10187809
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Fill & Empty connection to the faucet went bad.
Took the top & outside cover off to get to the connections for the Dishwasher. Installed the hoses & put washer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Moberly, MO
- Parts Used:
- WP3363394
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
water leaking out from under front of washer when it was in use
rolled washer up on its back used pliers to slide 2 hose clamps back on the hoses. pulled both hoses off pump. There are 2 metal type latches holding pump in place. Remove those by prying off with a screwdriver then you can remove the pump by lifting it off the motor shaft. Then install new pump on shaft making sure to align the square shoulders on pump shaft with water pump slots. Then just reverse the removal process hook water up and test to make sure no leaks. My pump had been dropped sometime between the factory and my getting it so I had to glue it back together where it had separated. Easier to fix than to send it back for replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix from Northridge, CA
- Parts Used:
- WP3363394
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Water leaking when using washing machine
First I had to have my wife help me tip the washing machine over so we can get at the pump which we suspected was leaking.
We searched partselect.com and found the part and ordered it and it arrived after a few days.
At first the part won't fit because the metal rod that was supposed to rotate the pump was badly rusted. So we had to buy a file set ($9.95) from Home Depot to file the rust away so that the part will fit.
Filing took a long time to do and was very tedious but after the metal rod was filed away, the pump fit and that's all it took.
There were actually only 2 clamps you have to remove. One at the back and one out front that holds the pump in place. After removing those clamps then it was easy to attach the new pump (after filing the metal rod).
Thanks partselect.com :-)
We searched partselect.com and found the part and ordered it and it arrived after a few days.
At first the part won't fit because the metal rod that was supposed to rotate the pump was badly rusted. So we had to buy a file set ($9.95) from Home Depot to file the rust away so that the part will fit.
Filing took a long time to do and was very tedious but after the metal rod was filed away, the pump fit and that's all it took.
There were actually only 2 clamps you have to remove. One at the back and one out front that holds the pump in place. After removing those clamps then it was easy to attach the new pump (after filing the metal rod).
Thanks partselect.com :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Crossville, TN
- Parts Used:
- WP3363394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Leaking pump
Replaced with new pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Romeoville, IL
- Parts Used:
- WP3363394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
The drain pump was leaking water.
The repair was easy. Disconnected the water and drain lines. Tipped the washer on its back and used pliers to remove the clamps holding the drain lines. The pump was replaced and reattached to the drain lines.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PLEASANTON, TX
- Parts Used:
- WP3363394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water pump replacement
Job was not as bad as I had thought it would be. This sites instant repairman was a really big help ! I did not take the back off, instead I just put machine on its back and changed out the pump from the bottom. Worked out great and was faster.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrence from Independence, MO
- Parts Used:
- WP3363394
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Original pump leaking
Removed cabinet, removed pump, installed pump (very easy), replaced cabinet (somewhat difficult until I figured out that I was installing a clip backward).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brandon from Bellingham, WA
- Parts Used:
- WP3363394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Leaking washing machine.
First I removed the back of the machine after unplugging it and disconnecting from the water supply.
Then removed the shell.
Put water in the machine directly into the bin with a hose. Then watched for leaks. I immediately noticed the pump housing was leaking. So I removed the pump got the part number and ordered it online on this site.
The pump came in 3 days and I installed it. The hard part was putting the frame back on since it was slighly bent from another repair.
Other than real simple and I had my machine fixed for $37.
Then removed the shell.
Put water in the machine directly into the bin with a hose. Then watched for leaks. I immediately noticed the pump housing was leaking. So I removed the pump got the part number and ordered it online on this site.
The pump came in 3 days and I installed it. The hard part was putting the frame back on since it was slighly bent from another repair.
Other than real simple and I had my machine fixed for $37.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Pencil Bluff, AR
- Parts Used:
- WP3363394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Water leaking from water pump housing.
Removed the two clips holding the pump to the motor, Lift pump off motor and twist pump to allow easy access to hose clamps. Slide clamps off of pump housing, remove hoses and reverse the process just described.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Macon, GA
- Parts Used:
- WP3363394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
water pump
It was really simple. All I had to do was take the outside body off of the washer & undo the clamps & take the old water pump off & put the new one on & put the clamps back on & put the body back on. It was easy & a whole lot cheaper than buying a new washer. Thanks for being there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Niles, OH
- Parts Used:
- WP3363394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer leaking in front
Got the part in two days! After watching the installation video, i figured i could take the pump off without removing the complete washer panel. Tipped washer on to back and there was the old pump staring at me. Disconnected the two hose clamps with pliers (easy). Hardest part was removing old pump due to crud and rust. Removed pump clamps and forced it off with end of screwdriver alternating both sides. This is why the video shows panel removal. Would have been much easier i think! I used fine sandpaper to get the shaft cleaned up and put a few drops of liquid hand soap into opening of new pump. Lined up the pumped with shaft and it slid right on. Reattached hoses and pump clamps and done!! NO more leak!! Really easy repair - about 15 minutes total.
Was this instruction helpful to you?
Thank you for voting!