Models > 2043499990 > Instructions

2043499990 Kenmore Upright Vacuum - Instructions

Jump to:

All Instructions for the 2043499990
61 - 75 of 306
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Vernon from INDEPENDENCE, MO
Parts Used:
WP3363394
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
pump seal leaking
I shut off the water supply hoses and then disconnected them and also disconnected the power supply cord--next I laid the washer on its back being sure to place a block near the water supply valve so the weight of the washer does not rest on the water valve--next I disconnected the inlet and outlet hoses from the pump--next pop off the two retainer clips on the pump and then remove the pump by sliding off of the motor shaft-----to re- assemble just reverse the procedure and you are done--it is a very easy fix.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from DELANO, MN
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
We were getting small water spots on floor near front of washer but could not find source of leak
Unfortunately my washer cabinet did not come off as in the video so I had to do repair from underneath. The rest of the repair worked exactly like the video showed. I had a couple of small, sturdy wood boxes about 9" high which I used to brace the washer after tipping it backwards a bit (and unplugging it too). My wife acted as a spotter to be extra safe. The only two things that required the hook tool and mirror were: 1) Working from the bottom my hands were at an awkward angle so I couldn't pop the retainer clips off the pump, but a hook tool (like a screwdriver with a hooked end) popped them off easily, and 2) The other issue was once the new pump was in place I could not locate the slot for the top retainer clip until I could look at it with the telescoping handle mirror, and then I was able to put the clip in by feel. Extremely easy repair, especially with the guidance from the video. Thanks for video help! WH
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Sun City, AZ
Parts Used:
WP3363394
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
leaky water pump
First unplug washer and turn water off (both hot and cold) You only need to pull washer out away from wall about 1 1/2 feet. Take a putty knife and slide under the front corner of the control panel ( both sides one at a time) lift up corner as you slide putty knife under the corner. After both sides are released on the control panel slide control panel forward( about an inch) to release rear of panel and flip panel over the top. Unplug the lid safety switch then with a screw driver unsnap the cabinet straps one on both sides that were under the control panel. Put screw driver into the spring strap end closest to you and push screw driver back which will release the straps( one on each side). Next tilt the cabinet toward from the back( about 6 ") and lift up about 2 " the cabinet can now be removed. Undue the two hoses on the water pump that is located at the bottom of the washer in the front ( make sure you catch the water from the hoses in a small pan). Undue the two spring clips that hold the pump on. Pull pump straight out (about 1 ") discard old pump and install new one in reverse order. When reinstalling the cabinet there are two stubs on the bottom bracket on the washer that have to put into the slots in the lower front corners of the cabinet ( the hardest part of the whole project is putting the cabinet back on, the trick is what I described above with the slots in the lower front corners. Good luck it very easy to do.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RAYMOND from ISLESBORO, ME
Parts Used:
WP3363394
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Water leaking on the floor.
Of course I tried to determine where the leak was from. There wasn't a solid flow of water and was confined to the front. Pulled the washer out and laid it down. Noticed that a metal clip had a little corrosion on it and followed it back to the water pump seal. Removed two hoses and unclipped the pump. That's it. No screws or nuts. Looks like it was expected to fail and was easy to replace. It did last for 20 years though.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leon from rockland, MA
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Pump was leaking
First I watched the repair video. Then I pulled the power plug and shut the water off. I didn't have all the room available to remove the front and sides of the machine in my narrow hallway so I just slid it away from the wall and leaned it back against the wall and had plenty of room to do the repair lying on my side. $28.00 part and in 20 minutes all done. This is the second time this site saved me time and mucho money. Thank you. Leon B. from Massachusetts
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
chriss from AVILLA, IN
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
leaking water
laid washer on side, used butter knife to pry off spring clips. there is just enough room to get pump off the shaft .Unhook two hoses then install new pump.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from San Saba, TX
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers
water on floor
Frist I removed the two water hoses going to the pump. Second releaseed the two clips holding the pump , it came right off the motor shaft.
Third, put the new pump on the shaft, put the clips on last the hoses good to go.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
douglas from thompsontown, PA
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
A leaking pump
My husband got the part within 2 days of the order and replaced the leaking pump within a half hour. The repair was very quick and easy for him and your company's prompt delivery prevented my floor from getting wet everytime I did a load of laundry. Thank you and we will continue to get parts from your site in the future--hopefully we won't need to anytime soon. but we know you are there if we need to repair!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Stone Mountain, GA
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Washer Leaked At Bottom
I watched the instructional video on how to take apart and how to take washer a part and how to install the direct drive water pump. It was very easy to do. also the delivery was very fast. I will be using the site to fix other appiances that I have that is sitting around broken. Thanks for your speedy service and customer service.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Doug from ANN ARBOR, MI
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Washer was leaking from the middle front of the machine
The repair went fine and the U - Tube video was very helpful. However, the putty knife under the front corners to release a spring clip was not accurate to release the console. Our Roper had two philips head screws on each corner of the back of the console that had to be removed to allow the console to slide back and off its clips. Then the housing of the machine (sides and front) was not coming off as described. However, after measuring I determined that the water pump had enough clearance to be removed without the housing of the machine being removed. So, the repair was even simpler than described.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
leon from hialeah, FL
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
direct drive water pump
very well the part was easy to install and the part was easy to find on the diagram furnished by parts select
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
richard from Hermon, NY
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
seal was leaking on the pump
plires took off the two hoses , on clip the two snap clips . pulled out the old pump . put the new one in cliped in the snap clips in & hook the hoses back up
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James P from Eureka Springs, AR
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Pump leaking at shaft
Remove four screws securing control panel from the rear and tilt control panel forward. Unplug wiring harness from door limit switch. Unsnap and remove two S-clamps securing enclosure to back panel. Tilt enclosure slightly forward and remove it from wash machine. Disconnect water hoses and clips securing water pump and remove water pump. Install in reverse order. Caution: inspect water hoses closely. I had a rotten pump intake hose and found out the hard way (water everywhere).
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Louisa, KY
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Water Pump was Leaking
I disconnected the washer from the water supply lines.turned the washer on it's back. took two hoses off the water pump.Unsnapped two spring clip's.Took the old pump off and installed the new pump.That is all there was to it.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Merrimack, NH
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
The water pump was leaking
The new pump arrived at my door just a few days after it was shipped.

Once I got the water hoses off and the clips holding the pump I had to use a large screwdriver to get the pump off the motor shaft. I then tried putting the new pump on but it wouldn't fit. I noticed that the motor shaft was flaired out (possibly due to rust) so I used a Dremel Tool with a grinding disk to carefully grind down the shaft to what it looked like it was supposed to be. Once that was done the pump easily slipped into place. I attached the pump clamps and hoses and pushed the washer back into place. I ran a quick test and then later a load of laundry. No more leaks!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 2043499990
61 - 75 of 306