Models > 2043499990 > Instructions

2043499990 Kenmore Upright Vacuum - Instructions

Jump to:

All Instructions for the 2043499990
121 - 135 of 306
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Judy from Columbia, MO
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set
Water was leaking from under the machine
I slid the washer out so that I could access the bottom. I laid it on its side so I could look underneath. It was obvious that the leak was caused by a worn water pump bearing. I removed motor/pump assembly which required removing the nut at the top of the agitator and three bolts holding the motor assembly to the washer. I removed the assembly and water hoses then reversed the process with the new pump. In all it took about an hour to an hour and a half.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Princeton, NJ
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Water leaking from washer
First I unplug electric plug, then turn off water lines & disconnected them. Pulled out the washer where I could easily work on it. Then removed the screws holding the back panel and top control knob panel by separating it from main body. (Spring clips on control panel were a bit tight to pop off.) Once removed back & top, the main body of washer, hinges forward and pulls out and off. Now the pump is accessible, so I remove the two hoses clamps and pull off hoses, and pop off two spring clips holding pump on the motor. Then I slide new pump onto the motor, (line up flat spot on shaft with pump) and pop the spring clips back on and reconnect the hoses and clamps. Put main body, back and top control panel back together the opposite of the way I took it a part. Moved washer back and reconnected water lines and plugged in. No more water on the floor… (Note:) Washer leak happened on Sunday & Monday was holiday of coarse. So I ordered the new pump Sunday online and it arrived by Wednesday. Thank You PartSelect.com.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Morgantown, PA
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Washer was leaking
First I remoived the 2 screws that hold on the control panel and tilted it back. Next I removed the clips that retain the lower enclosure and tilted it forward to remove it. With the lower enclosure out of the way I used pliers to remove the 2 hose clamps on the pump and a screw driver to undo the retaining clips. Installed the new pump and reassembled everything in the reverse order. The only trrouble I had was in getting the lower enclosure back on correctly. It took a little effort to get everything lined up so it would fit.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jesse from Richardson, TX
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Small amout of water on floor near front of washing machine
Turned water off at wall and disconnected electrical power cord from outlet.

Tilted washer backward far enough to view water pump and bottom of tub, motor, etc.. Saw drip of water on one of the two clamps that secure the pump on shaft.

Removed the two hoses that are connected to pump (drained water in a pan). Using screw driver, removed the two clamps that hold the pump on the shaft. Wet, greasy shaft allowed pump to slip off easily.

Installed large hose onto new pump, then put new pump onto shaft...then aligned four pump legs in place, then snapped the two clamps on to secure pump in place on shaft.

Installed second hose.

Kim, ar PartSelect.com was great!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RICHARD from SUGARHILL, GA
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
water would not drain
Replacing the motor was easy after watching the video on partselect. Unfortunately it turned out to be the safety switch on the lisd was broken.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from maple hts., OH
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
water leaking from under washing machine
I was not able to get the the job done as the video, i pulled the electric cord.Shut water lines down place washer at about 45 degree angle lay on floor, removed hose clamps, remove metal clamps on each side of pump, removed pump, replace with new pump and reverse order in which pump was remove,
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Derrickon from Norfolk, VA
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
Water Leaking
I watched the video on the website and the repair was fairly easy to perform. The hardest part was the beginning, unhooking the panel on both sides of the control panel and pulling the control panel backwards. The panel was a little bit harder to release than the video suggests (ok, a lot harder) and took a little time. Other than this minor setback, the repair was very easy. If I can do this, anyone can this and look very handy in the process.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leonid from Suffern, NY
Parts Used:
WP3363394
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Washer was leaking when I moved into my new house.
First disconnected water hoses, put machine on the back, removed hoses from the pump, then removed two metal retainers that hold the pump. Motor's shaft got so rusty, that I could not remove the pump. I spent two days (few hours each day), until I finally was able to snap it off. If that wasn't difficult enough, putting new pump on was even harder. Metal rusted thru, and expanded from long leaking (previous owners probably had this problem for a while). I spent a lot of time filing it down with dremel tool, until finally I was able to attach the pump on the motor. I almost gave up in the process, but I'm glad I didn't, it works great. Motor might fail soon tho due to the rust.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Darrell from Corpus Christi, TX
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
water leaking from washing machine, water pump
Followed instructions on site, remove two screws holding contol panel and flipped up, disconnect water level tube(clear plastic), pry off two metal clips holding shell to back(on top,under control panel), remove shell. Water pump in front, bottom, two hoses. Remove hoses, pry off two metal clips
securing water pump. Water pump stuck on. Soaked with penetrating oil and let sit awhile. Reach behind pump and pry off. Turn impeller on new pump to align with flat sided shaft with finger in where hose connects. Slide pump onto shaft, tap lightly to get all the way in, put clips back on pump(tight), and hoses back on. Put shell back in place, clips back on top, water level hose back on panel, panel down, screws back in. Run machine, watch for leaks(water on floor). Had never done this before, this site made it easy. Thanks.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Don from wahoo, NE
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
leaking after wash cycle
The new pump should have come with an explosive charge to remove the old pump, but the new pump was an exact match and ground shipping was super fast.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Rockaway, NJ
Parts Used:
WP3363394
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Leak in the right front of the washing machine.
I found a Instructible.com project that showed how to open the washer case--it took about three minutes to open once I knew what to do. 20 minutes, including looking at the tutorial.

I matched the parts with pictures on this site, and had it mailed in. 20 minutes

It took about twenty minutes to get together some 2x4 lumber and a flat pan to catch the waste water that was sure to come out of the drain hose. With the washer tipped up and the pan under the pump, I pulled the hose clamps and hoses easily.

The pump was rusted to the shaft of the motor, so took about ten minutes of persuasion with a large screwdriver and a lot of rocking back and forth before it came off the shaft. I then sandpapered some of the rust off, and slid the replacement pump on. Next time I would fit the hoses on first--it would have been easier. The pump did not slip on easily, so a little tapping with a light hammer got it onto the motor shaft. I was concerned about damaging the bearing or seal of the pump, so was very gentle. With more time and better tools, I would have cleaned the shaft off completely.

The case went together as easily as it came apart, in about three minutes. I carefully mopped and dried the area the pump was in, and ran an empty cycle through the washer. I checked back during the next several loads, and the floor remained dry.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gordon from Asheville, NC
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
pump was leaking
The pump was leaking through a small portal on the front. I do not know what purpose the portal which was covered served...but that was the portal (half moon shaped) that was leaking. I decided to try and glue it with poly epoxy...glued it once, checked for water leak and then added more glue..waited overnight for glue to dry. I reinstalled the glued pump and it is working fine. The new pump is now on my shelf for backup. Taking the old one off and reinstalling is no problem. follow suggestions of others at this site.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathleen from Benton City, WA
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Leaking Pump
1) Turned off power
2) Tilted washer on to its back legs and the wide held it there.
3)Removed the inlet and outlet hoses on the pump using channel lock pliers.
4) Using screw driver I detached the clips that hold the pump in place.
5) Removed Pump
6) Inserted new pump attaching the clips to hold it in place.
7) Attached the hoses.
8) Set washer back on all four legs and washed a load of clothes to confirm that the leak was fixed. Actually you could see a discolored spot where the water had been running from the pump shaft seal so it seemed pretty obvious that it was the culprit.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rick from Slaughter, LA
Parts Used:
WP3363394
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Leaking water
Checked the repair suggestions online. It said the water pump was the problem 75% of the time. I ordered the part and in 20 minutes the problem was fixed.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Poway, CA
Parts Used:
WP3363394
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
There was a leak from the bottom of the machine.
I disconnected the power, hot and cold water feed lines and the drain line. (Be sure to turn off the water sources before removing lines from machine.) I pulled the machine away from the wall and laid it on its back. Have a bowl or container to collect the water from the drain and some towels for incidental spillage. With a pliers, remove the two water hoses (inlet and outlet) from the pump, right on the bottom of the motor. The pump is held on by two metal clips that are pryed off with a screw driver. The pump pulls straight off of the drive shaft. To avoid frustration when setting the new pump, be sure to align the insert point on the pump with the shaft. The two retainer clips can be reset by hand. Reattach the inlet and outlet hoses, set the machine upright, reattach the drain line, hot and cold water lines and move back into place. Plug the machine in and turn on water sources. Easy-peasy.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 2043499990
121 - 135 of 306