2048778180 Kenmore Upright Vacuum - Instructions

Just removed the old pump with a pair pliers and snapped the new one on. It was a snap

I shut off the water supply hoses and then disconnected them and also disconnected the power supply cord--next I laid the washer on its back being sure to place a block near the water supply valve so the weight of the washer does not rest on the water valve--next I disconnected the inlet and outlet hoses from the pump--next pop off the two retainer clips on the pump and then remove the pump by sliding off of the motor shaft-----to re- assemble just reverse the procedure and you are done--it is a very easy fix.

I Removed hose clamps and 2 pump clamps. I took the old pump(had a small hole burned in it) off and replaced it with the new pump. I replaced the 2 pump clamps and the hose clamps and it was ready to go.

Unplugged the washing machine. Removed the two philipps screws holding the control panel. Swung it up , disconnected interlock connector, and pried the two clips. Removed the top and cabinet assembly to have easy access to the leaking pump.
Disconnected the two hoses connected to the pump. Used the plier to loosen the hose clamps. Removed the two retainers securing the pump. Removed the old and damaged pump and replaced with the new one. Reinstalled the retainers back on. Reconnected the hoses and clamps. Put the top and cabinet assembly back on. Snapped back the clips and reconnected the interlock connector. Screwed the control panel assembly to the cabinet. Done. Ran the washing machine to check for leaks. Found none.

First of all, it would have been helpful to have two people take the housing off the frame. One to lift and the other to disconnect the hoses that need to come off the pump and the filler.

Second, THANK YOU to another person that posted about prying the pump from the motor and sanding it to accept the new pump. When I couldn't get the pump off the motor due to rust, I thought both the pump and motor were done. But I worked the pump off the motor shaft (I had to break the old pump, but it was toast anyway) and used a wire brush and sandpaper to clean the shaft. When I got the new pump, it slid on like a champ!

I also used the parts list that came with the washer to make sure I got all the parts back together in the right place. Like I said, I took too much apart and didn't pay attention to what I was doing for later reassembly. Even though the parts list that came with the washer is small and not to scale, it helped me put the thing back together.

I got my part when PartSelect promised and I got help here from the website. I will use this company whenever I need an appliance part.

rolled washer up on its back used pliers to slide 2 hose clamps back on the hoses. pulled both hoses off pump. There are 2 metal type latches holding pump in place. Remove those by prying off with a screwdriver then you can remove the pump by lifting it off the motor shaft. Then install new pump on shaft making sure to align the square shoulders on pump shaft with water pump slots. Then just reverse the removal process hook water up and test to make sure no leaks. My pump had been dropped sometime between the factory and my getting it so I had to glue it back together where it had separated. Easier to fix than to send it back for replacement.

First I had to have my wife help me tip the washing machine over so we can get at the pump which we suspected was leaking.

We searched partselect.com and found the part and ordered it and it arrived after a few days.

At first the part won't fit because the metal rod that was supposed to rotate the pump was badly rusted. So we had to buy a file set ($9.95) from Home Depot to file the rust away so that the part will fit.

Filing took a long time to do and was very tedious but after the metal rod was filed away, the pump fit and that's all it took.

There were actually only 2 clamps you have to remove. One at the back and one out front that holds the pump in place. After removing those clamps then it was easy to attach the new pump (after filing the metal rod).

Thanks partselect.com :-)

The repair was easy. Disconnected the water and drain lines. Tipped the washer on its back and used pliers to remove the clamps holding the drain lines. The pump was replaced and reattached to the drain lines.

Replaced with new pump

First I removed the back of the machine after unplugging it and disconnecting from the water supply.

Then removed the shell.

Put water in the machine directly into the bin with a hose. Then watched for leaks. I immediately noticed the pump housing was leaking. So I removed the pump got the part number and ordered it online on this site.

The pump came in 3 days and I installed it. The hard part was putting the frame back on since it was slighly bent from another repair.

Other than real simple and I had my machine fixed for $37.

Removed cabinet, removed pump, installed pump (very easy), replaced cabinet (somewhat difficult until I figured out that I was installing a clip backward).

As noted by other users, I tipped the washer on its back to access the water pump underneath. First I had to drain several gallons of water out...I removed the end of the drainage hose from my main basement drain and placed it into a large bin on the floor and it drained itself. Then I removed the two spring clips from the old pump and took off the two hoses. The pump pulled free easily from the drive shaft. I put the new one on, reseated and reclipped the hoses to the pump, and put the washer upright and it worked immediately. Easy repair...saved hundreds on buying new washer.

I did my troubleshooting on line. I took the water pump off, flushed it out, and used a coat hanger to ensure the hoses were not obstructed. Put the water pump back on and reassembled the washer - still would not drain. Checked the lid switch by listening to hear it click, which it did. So, I assumed it was the water pump, so ordered one. Two days later my son-in-law said he experienced the same problem, but it was the lid switch. I decided to check the switch again, this time using my hand to see if it was securely fastened. As soon as I grabed the switch, it sprung apart. I removed it and followed the instructions on how to hot wire the connection for a by pass, and the washer drained. Needless to say I ordered a lid switch assembly. Now I have a new water pump as a backup :) Lesson learned. Opinion: the lid switch assembly is very cheaply made.

It was really easy.I tilted washer and removed the clamps holding on the drain hoses and clips holding the water pump and reinstalled the new one.

I pulled washing machine away from the wall . Unplugged unit. Turned off water and disconnected hot and cold water line. Laid washing machine on its side. Disconnected inlet and outlet lines from pump using a pair of pliers to squeeze hose clamps to enable removal of hoses. FLASHLIGHT is needed to view area. Pop off spring clips with a small screw driver. It's a little difficult getting hand back to remove back spring clip. Water pump has fitted stand offs that let the pump be installed and removed very easily and also enables proper installation orientation. Make sure you have a pair of gloves on to avoid sheet metal cuts during removal and installation.