2048778180 Kenmore Upright Vacuum - Instructions

Unfortunately my washer cabinet did not come off as in the video so I had to do repair from underneath. The rest of the repair worked exactly like the video showed. I had a couple of small, sturdy wood boxes about 9" high which I used to brace the washer after tipping it backwards a bit (and unplugging it too). My wife acted as a spotter to be extra safe. The only two things that required the hook tool and mirror were: 1) Working from the bottom my hands were at an awkward angle so I couldn't pop the retainer clips off the pump, but a hook tool (like a screwdriver with a hooked end) popped them off easily, and 2) The other issue was once the new pump was in place I could not locate the slot for the top retainer clip until I could look at it with the telescoping handle mirror, and then I was able to put the clip in by feel. Extremely easy repair, especially with the guidance from the video. Thanks for video help! WH

I watched the instructional video on how to take apart and how to take washer a part and how to install the direct drive water pump. It was very easy to do. also the delivery was very fast. I will be using the site to fix other appiances that I have that is sitting around broken. Thanks for your speedy service and customer service.

very well the part was easy to install and the part was easy to find on the diagram furnished by parts select

The repair went fine and the U - Tube video was very helpful. However, the putty knife under the front corners to release a spring clip was not accurate to release the console. Our Roper had two philips head screws on each corner of the back of the console that had to be removed to allow the console to slide back and off its clips. Then the housing of the machine (sides and front) was not coming off as described. However, after measuring I determined that the water pump had enough clearance to be removed without the housing of the machine being removed. So, the repair was even simpler than described.

I press using the plier the spring retainer to removed the two hose from the defective pump.
I used screw driver to removed the two retainer.I pulled the pump away from the shaft of the motor. Replaced with new pump, align to the motor shaft and return back the two retainer. It is easy and its good to have my parts right on time.

1) Disassembled the lid
2) Took the front Panel off (the old water pump was in the bottom left hand corner in plain site).
3) Used flat head screw driver to gentle pry the top and bottom water pump fasterners.
4) Used pliers to remove top hose camp. Note this is where I discovered why everyone says to put the washer on it back. Water came rushing out. Luckily no damage to the motor.
5) Used pliers to remove the bottom hose clamp.
6) Put everything back together Total time <30 minutes.

Unfortunately, the water is still not completely draining. I am now looking at the hoses for obstructions. Any other suggestions?
Thanks

I unplugged the washer, put a towel down, leaned it back and held it up with one hand while undoing the clamps with plyers. Pulled the two clamps off, pulled the pump, put the new pump on, reattached the clamps. Most of this with one hand while the other held the washer at an angle.

Removed water supply hoses and took drain hose out of drain. Unplugged electrical cord. Turned washer over to see and reach pump easily. Flipped clips holding water pump. Moved hose clamps back on inlet and outlet hoses. Wiggled hoses off pump. Placed new pump and flipped clips back in place. Wiggled hoses back onto pump ports and replaced clamps to hold. Turned washer upright and reinstalled. Using channel lock pliers to move hose clamps was the hardest part.

Removed the four screws from the control housing. Disconnect wire to machine housing. Remove the two clips connecting the machine housing to the back. Remove washing machine housing. Pump is located right in front. Disconnect hoses, remove and replace pump, reconnect hoses. Replace the machine housing. This was the hardest part if all trying to reinstall the housing.Once you get the machine housing in place correctly, put everything back together. You just saved about $125 in fifteen minutes.

plires took off the two hoses , on clip the two snap clips . pulled out the old pump . put the new one in cliped in the snap clips in & hook the hoses back up

I disconnected the washer from the water supply lines.turned the washer on it's back. took two hoses off the water pump.Unsnapped two spring clip's.Took the old pump off and installed the new pump.That is all there was to it.

I read the trouble shooting guide on your web sight to figure out what the problem was and after checking the hoses the pump seemed the next most likely problem. So I ordered the part.My main problem was the lack of room to work,if I could have tipped it on it's back or raised it I would not of had a problem.But I tipped it up and blocked it from falling and removed the part while waiting for the new one to arrive.Once it arrived it only took a few minutes to install.When I tried the washer it still leaked water,so I tipped it back up to check it out.The only thing that was wrong was that the spring hose clamps had not seated yet so I moved them around and wiggled the hoses to try and get them tighter.The next time ,it worked fine.The other reviews and trouble shooting guide were a great help!

It was the first time I ever ordered parts online or even attempted to repair a washer. You all have made finding and ordering the right part very easy. I got the part in 2 days even though I used the cheapest shipping option (5 to 7 days). I turned off the water, removed the water lines so I could lay the washer on its side. No tools were needed to remove the water pump, just two clips held it on. I put the new pump on, hooked up the water and washed a load that night.

Frist I removed the two water hoses going to the pump. Second releaseed the two clips holding the pump , it came right off the motor shaft.
Third, put the new pump on the shaft, put the clips on last the hoses good to go.

laid washer on side, used butter knife to pry off spring clips. there is just enough room to get pump off the shaft .Unhook two hoses then install new pump.