2048778290 Kenmore Upright Vacuum - Instructions

Removed water supply hoses and took drain hose out of drain. Unplugged electrical cord. Turned washer over to see and reach pump easily. Flipped clips holding water pump. Moved hose clamps back on inlet and outlet hoses. Wiggled hoses off pump. Placed new pump and flipped clips back in place. Wiggled hoses back onto pump ports and replaced clamps to hold. Turned washer upright and reinstalled. Using channel lock pliers to move hose clamps was the hardest part.

I press using the plier the spring retainer to removed the two hose from the defective pump.
I used screw driver to removed the two retainer.I pulled the pump away from the shaft of the motor. Replaced with new pump, align to the motor shaft and return back the two retainer. It is easy and its good to have my parts right on time.

Pull Washer out, Flip to the right on it's side. Pop two Metal retaining clips, squeeze hose clamps with pliers. Remove pump, sand shaft with dremil or 80 grit sand paper. Replace with new pump. Easy! Push washer back and attach hoses and power. Done 15 minute repair

Removed the four screws from the control housing. Disconnect wire to machine housing. Remove the two clips connecting the machine housing to the back. Remove washing machine housing. Pump is located right in front. Disconnect hoses, remove and replace pump, reconnect hoses. Replace the machine housing. This was the hardest part if all trying to reinstall the housing.Once you get the machine housing in place correctly, put everything back together. You just saved about $125 in fifteen minutes.

Removed the two spring clamps from hoses; removed hoses from pump. Removed spring clips holding pump to motor. Had to pry pump off of motor shaft due to rust on shaft end. Sandpapered rust off of shaft and then lubed same with oil and new pump slid easily onto motor shaft. Re-snapped spring clips to hold pump onto motor and then reinstalled hoses and their spring clamps. Whala, end of story, job well done.

1) Disassembled the lid
2) Took the front Panel off (the old water pump was in the bottom left hand corner in plain site).
3) Used flat head screw driver to gentle pry the top and bottom water pump fasterners.
4) Used pliers to remove top hose camp. Note this is where I discovered why everyone says to put the washer on it back. Water came rushing out. Luckily no damage to the motor.
5) Used pliers to remove the bottom hose clamp.
6) Put everything back together Total time <30 minutes.

Unfortunately, the water is still not completely draining. I am now looking at the hoses for obstructions. Any other suggestions?
Thanks

I unplugged the washer, put a towel down, leaned it back and held it up with one hand while undoing the clamps with plyers. Pulled the two clamps off, pulled the pump, put the new pump on, reattached the clamps. Most of this with one hand while the other held the washer at an angle.

Unplugged the washer. Pulled it away from the wall far enough so it would be stable tilted back against the wall. That way I didn't have to disconnect any hoses or lay the machine down.

I used a ViceGrips to squeeze the hose clamps and then pulled the hoses off. Getting the pliers in the right position in the tight space was the hardest part of this whole job, and that still wasn't particularly hard. I have medium sized hands (for a man).

I flipped open the retainer clips with my fingers. Pulled the pump off and slid the new one on. It helped to make sure first that the flat side of the motor shaft was roughly facing the same way as the slot in the pump.

I reattached the hoses and popped the retaining clips back on. Held my breath and ran the washer. No more leak!

Incidentally, before I discovered PartSelect I called Whirlpool service. I asked if they could have the tech show up with the part. They said "No." I'd have to pay the fee for a diagnostic visit and then the tech could order parts and return to install them. They said there would be no service charge for the return visit.

Several years ago I believed this story when I called for a dryer repair. However, when a second technician returned with the part I had told the dispatcher the first time around was needed, he came up with some excuse why there had to be a supplemental service charge. I challenged it on my credit card and eventually got it removed, but it was a hassle.

Thank you PartSelect! And thanks to others who posted their experiences and gave me confidence to fix it myself.

Disconnected power, water, and drain then moved washer away from wall. Put down some 2x4's to protect hoses and flipped washer on its back. Removed hoses with pliers, removed clips holding pump to shaft, and installed new pump. Reversed process and tested with just water be fire washing clothes.

Just removed the old pump with a pair pliers and snapped the new one on. It was a snap

I shut off the water supply hoses and then disconnected them and also disconnected the power supply cord--next I laid the washer on its back being sure to place a block near the water supply valve so the weight of the washer does not rest on the water valve--next I disconnected the inlet and outlet hoses from the pump--next pop off the two retainer clips on the pump and then remove the pump by sliding off of the motor shaft-----to re- assemble just reverse the procedure and you are done--it is a very easy fix.

laid washer on side, used butter knife to pry off spring clips. there is just enough room to get pump off the shaft .Unhook two hoses then install new pump.

First I watched the repair video. Then I pulled the power plug and shut the water off. I didn't have all the room available to remove the front and sides of the machine in my narrow hallway so I just slid it away from the wall and leaned it back against the wall and had plenty of room to do the repair lying on my side. $28.00 part and in 20 minutes all done. This is the second time this site saved me time and mucho money. Thank you. Leon B. from Massachusetts

The repair went fine and the U - Tube video was very helpful. However, the putty knife under the front corners to release a spring clip was not accurate to release the console. Our Roper had two philips head screws on each corner of the back of the console that had to be removed to allow the console to slide back and off its clips. Then the housing of the machine (sides and front) was not coming off as described. However, after measuring I determined that the water pump had enough clearance to be removed without the housing of the machine being removed. So, the repair was even simpler than described.

I followed the you tube instructions. The hardest part was realigning the washer housing on the lower frame.