2048778290 Kenmore Upright Vacuum - Instructions

After unplugging power and disconnecting water drain hose, I pulled the washer out aprox four feet from the wall and leaned it back against the wall. I then used a lamp at the end of an ext cord to light up below the washer where the water pump was attached and it was easy to remove and replace! I carefully replaced the washer in its original location and reconnected power and drain hose. The job was complete in 15 minutes! Wow!

removed two hose clamps and two metal clips
removed old pump and replaced with new
wish all my plumbing was that easy
order Thursday night got it Monday
great job
I'll be telling everyone that needs parts about you
thanks

I pulled out the washer, laid it on it's back, pulled off the two hoses using pliers for the clamps, pulled back two clips, pulled off the pump from the shaft, put the new pump on the shaft, and did the reverse of the above. It was a simple operation and made even more satisfying by the prompt delivery of the part, within 2 days. Thank you for that, and I will use your services in the future if needed.

Kayla tilted the washer backwards so I could get access to the pump from below. all I had to remove was two clips then slid the old pump off the shaft and the new one on-clip it in place.Then clamp the hoses on the new ports and we were done in about ten minutes.This made me feel good in three ways... Did A job with my daughter! Save a lot of cash!! and walk away with a great sense of accomplishment !!! Rob@kayla

This was very easy. I just pushed the retaining clips off of the pump body (one top side, and one on the bottom) with my fingers. Then I used a pair of channel lock pliers to compress and relocate the spring clamps down the two hoses away from the pump body to remove their clamping action. I removed the hoses, then pulled the pump off of the motor shaft. I lined up the motor shaft with the flat spots in the new pump and installed the new pump in the reverse order. This process took about five minutes and was super easy.

undone 2 hoses and popped off brackets

Installed long end first and snapped it into place.

watched a video that showed how to repair that you had on your web site. also read some of the remarks that other people left on site, one was super easy. just laid washer on its back, unhooked both water lines from pump. unhooked both metal clips holding pump and pulled off. replaced new pump in reverse order. didn't have to go thru all the procedures of taking off the body or nothing. 15min job.

tilted the unit on it's back. removed clamps and hoses from pump. used screwdriver and pried off 2 hold-down clamps. removed old pump. placed new pump onto shaft. installed hold -down straps. re-installed 2 hoses. stood washer upright, releveled and turned on.

I turned the washer on to see if I could determine where it was leaking from. After I figured out that it was the pump that was leaking, I ordered a new pump. I went with next day shipping because at our house, we can't go long without a washer and the cost for the shipping was worth it. Had it installed in 10 minutes, only tool needed was a pliers to remove the hose clamps, piece of cake repair!

My friend unplugged washer turned off water to it, tilted machine back took off old, put on new. It took him about 5 minutes. Washer is working fine now, no more water leaks!

I noticed a leak on the floor. I check the hoses for tightness on the back of the washer and the hoses going to the facets and drain. After disconnecting the hoses going to the washer, facet and drain, I then flip the washer on it's back and examined the underside for wetness. All the underside hoses appeared to be not leaking. I then disconnected the two hoses going to the pump with channel-locks, and I disconnect the two clips holding the pump with just my hand and removed the water pump. I then poured water into the hoses' opening on the water pump itself, and I discovered a slow leak occurring from the shaft area on the water pump. I searched PartSelect and luckily found a water pump that matched. I then installed the new water pump (after receiving it a few days later) in reversed procedures of disconnecting the old water pump. I tested the washer by adding a little bit of water into the washer then switch the dial to spin cycle in order to empty the water inside the washer--no leaks occurred and I was extremely happy.

Flip washer on its back, Undo/flip the clips/clamps off the water pump, remove the clamps from the hose and remove hoses from water pump, slide the pump off the direct drive, line up the shaft/drive with the new water pump and slide into position and return the clamps to secure water pump in place and reattach water hoses and clamp to the water pump. There should be two hoses going to the water pump, flip washer back upright and run a cycle to make sure the problem has been fixed

It was the first time I ever ordered parts online or even attempted to repair a washer. You all have made finding and ordering the right part very easy. I got the part in 2 days even though I used the cheapest shipping option (5 to 7 days). I turned off the water, removed the water lines so I could lay the washer on its side. No tools were needed to remove the water pump, just two clips held it on. I put the new pump on, hooked up the water and washed a load that night.

First, we took the pump off and found that it was leaking. Ordered the part on line. The part arrived in four days as scheduled. The small pump was easy to replace with screwdriver and pliars.