58RIAD Whirlpool Refrigerator - Instructions

Removed 4 screws, pulled unit out of slots, unpluged control wires plug and removed from fridg. Removed 3 screws that hold the motor module to unit. Then reversed procedure and had the batch of ice cubes one hour and fifteen minutes from the time I started replacement.

I ordered the part and just 1 1/2 days later, it arrived! Awesome!

I took the cover off the ice maker motor. Then I simply unscrewed the three screws holding the motor in place (be VERY careful - the hinge mechanism that holds the ice maker on/off bar needs to be gently removed from the motor so the prongs do not break).

Once the motor and ice maker hinge were removed, I simply pushed the new motor on, screwed all three screws back in, put the cover back over the motor, pushed the bar to 'on' and water flowed and ice was made! I turned it to Max so I would have lots of ice in a short amount of time then returned the switch to Normal and I've not had a problem since.

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started making ice in about 15 minutes. very easy fix

My husband is a plumber...but did not have time to make the repair. So I took it upon myself!

Super Easy!

1. Unplugged Fridge
2. Unscrewed the 3 screws on motor
3. Pulled out old motor
3. Had to pour some hot water to melt ice cubes that were currently in the shoot. (because the new part would not line up correctly because of the frozen cubes inside the maker). Then soaked up all the water with towels.
4. Inserted the new motor
5. Put 3 screws back in.

ICE, ICE BABY! Within a couple hours it was dropping ice into the bucket! Husband came home, and I told him I fixed the ice maker (his expression was of dread)...and then he checked it out and all was perfect! So proud!

exact part in with the new out with the old

3 Years ago our icemaker stopped working and we paid a professional $225.00 to come and repair. This time I chose to investigate the problem on line and PartSelect website gave me info on the motor assembly that may be the problem. Sure enough I purchased the part, it was delivered in two days. My husband installed the control & motor assembly in less than 15 minutes. We had ice within hours. Thanks for saving us a service call and the expense. The Goldbergs

replaced icemaker motor.easy peasy

Went very easy, watched the video from the web site and did what it showed to do and put it together and it worked.We now have ice.

I removed the two screws that hold the ice maker door. I then removed the single screw on the right underside of the ice maker. I depressed the plastic "catch" on the left underside of the assembly and the whole thing just pulled straight out. I then disconnected the wire harness.

The module cover is removed, then the module itself is easily removed by removing three screws.
The assembly is just as easy.

A few hours later, I had a half bucket of ice!

First I replaced the thermostat. (from this company.) Same thing happened. Then I thought the ice heater has too low voltage and does not melt it for extraction. So, I put a short on the relay on the beam receiver board. No difference. Then completely disassembled the ice maker, and discovered the shaft cracked on the plastic gear, which rotates the ice extractor. So, I ordered and received this control assembly. Put together the unit and having ice again. Due to the cracked gear the thing was out of timing. This gear drives the contactor for letting water in, freezing time, heating the ice, (so it slides out easily), etc

Removed ice maker from freezer area. Motor in ice maker was not rotating ice dump bar. Replaced control and motor assembly. Problem solved.

Removed end cover from ice maker assembly. Motor driven wheel had broken from its plastic shaft. Disconnect power source. Using philips screwdriver, remove three screws from corners of motor mold and remove mold. Per instruction on end cover, rotated strips arm ice ejection tines until they pointed in the two-o'clock position. Dry fit (without screws)new motor mold assembly to ensure that the shaft with flat engaged the socket with flat and that the new part assembly seated flat on icemaker housing re-install 3-screws. Re-connect power source. After 2 hrs. , Confirm that ice cubes are being produced.

my husband just took the motor off the existing maker and decided the front part of the unit was bad, I ordered it and it came in about 3 days he put the new front on it and screwed the unit back in the freezer, was about 4 screws I think. Didnt take too long but I would bet the next time it would be easier. Thank you

Followed the instructional video. It was not exactly like the unit I had but I followed as much as possible. I switched out the motor and within 3 hours had ice.

Replaced control and motor assembly ordered from you and unit started working.