58RIAD Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MARISA from MOUNT PLEASANT, TX
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My Ice Maker Has Plastic And Metal Parts, Of Course A Plastic Part Broke.
This was very easily repaired in about 15 minutes and only using a phillips head screw driver to remove 3 screws. The plate pulls off easily and there are no wires on this particular ice maker, only male and female clips . You may have to jiggle the metal wire ice on-off bar. The new face plate is all one piece and is installed the same way very easily. Plugged the refrigerator back in and had half a bucket of ice the next morning!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ardys from DeBary, FL
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Not making ice
I didn't, the young man who does all my maintenance work did it. He's super and can do anything. Thanks for making the repairs so simple, not having to pay the going service charge....I paid my Jim $25 compared to probably $65 by a service person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Orleans, MA
- Parts Used:
- WP628356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice maker arm mount
Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.
It would have been $150& $50 for visit to replace ice maker unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Granada Hills, CA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The contacts for the heater were burned out
The icemaker assembly came out after I unplugged the electrical supply and I cleaned the prongs on the heater and put it together and slid in the whole module back and plugged it in. Works like a charm. No tools were needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from Federalsburg, MD
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker not making oce
Remove tray that held ice then took off cover to the moter.removed three sewes that moter came off .then put on new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blair from Glenshaw, PA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
icemaker wasn't working
exactly like the video clip that the website had for the part - very easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Ellijay, GA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
ice maker will not make ice
Disconnect power cord turn off water supply. Remove four screws on bottom of ice maker unit.Then look for locking clips on bottom of @ near supports and remove unit sliding & cocking until you can turn motor toward you cord is just long enough pry motor control off with hand or flat blade screw driver buy pressing on side edges.Remove motor from unit by removing three screws & pull out of plug on one corner. [side by side unit not freezer over fridge like video].
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Beaumont, TX
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker stopped making ice
This is the 4th motor on this ice maker. Sears replaced the original motor at a cost of >$300 and this is the 2nd motor I have replaced at a cost <$70.
Repair is quite easy since this was the As described on your site, simply remove the door flap, remove the covering for the wiring, remove 3 hex nuts under the floor of the unit and the entire ice maker slides out. After disconneting the wires, you simply slide the cover from the motor, remove 3 philips screws and slide the old motor out.
Align the new motor, slide in, replace 3 philips and reverse the process to place the ice maker and hex nuts.
Was "back in ice" within an hour or so.
Thanks for the instructions and video and for making the parts affordable for do-it-yourselfers!
Repair is quite easy since this was the As described on your site, simply remove the door flap, remove the covering for the wiring, remove 3 hex nuts under the floor of the unit and the entire ice maker slides out. After disconneting the wires, you simply slide the cover from the motor, remove 3 philips screws and slide the old motor out.
Align the new motor, slide in, replace 3 philips and reverse the process to place the ice maker and hex nuts.
Was "back in ice" within an hour or so.
Thanks for the instructions and video and for making the parts affordable for do-it-yourselfers!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan from West Chester, PA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No ice in the bucket
I researched the problems on Kitchen Aid ice makers and found that this part failed within four years of service, took a chance and ordered the "Icemaker Control and Motor Assembly", it was the cause.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Bath, NC
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker stopped making ice
Placed ice maker control switch to OFF position. Removed wiring connection cover from ice maker. Disconnected wiring harness from ice maker. Removed old ice maker control and motor by removing motor cover and three screws. Installed new ice maker control and motor with the three screws and cover. Reconnected wiring harness and wiring connection cover. Placed ice maker control switch back to ON position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Los Lunas, NM
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The ice maker just quite working one day.
This repair was so easy I can not believe I waited so long to do it. What was I thinking?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from Westcliffe, CO
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The icemaker was stuck with ice cubes blocking ejection
After reading solutions to my problem on your website I ordered the part which fixes 50% of the problems. When I got back after Christmas the part had arrived. I removed the Icemaker and replaced the part. It took aprox. 20 minutes for the job. It was easy. Now we have ice cubes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracey L. from St. Paris, OH
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no ice
easy as pie everthing good thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wynnelle from El Dorado, CA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
freezer had stop making ice
My husband had taken the ice maker out and deceide which part we would need to fix the maker. your online parts list made this possible. The service you provide was most helpful. The shippment got it to us in record time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Giles from Sun City, AZ
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
non functioning ice maker
followed instructions from Partselect on- line video.
Was this instruction helpful to you?
Thank you for voting!