Models > WRX735SDBE02 > Instructions

WRX735SDBE02 Whirlpool Refrigerator - Instructions

Jump to:

All Instructions for the WRX735SDBE02
91 - 105 of 275
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mario from EL PASO, TX
Parts Used:
WP67006331
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
the locking latch to the water filter cover had been broken for a while
Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from SWANVILLE, ME
Parts Used:
W11338583
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Freezer Bulb failed
Unscrewed bulb from sock .
Replaced with new one . Now working
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from WALLA WALLA, WA
Parts Used:
WPW10300024
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
original ice maker would make ice and then water would over flow into ice bin and freeze
stick the very small screw driver in the hole on the left side cover and lift up to release the keeper tab,pull out to expose the wire connecter.insert the small screw driver in the slot on the left side to release the tab while pulling apart the two connectors.tuck the wires tight to side and pull out the ice maker.I thought I was getting the whole ice maker assembly,but just got a part of it,so I had take it apart and put it back together.the hardest thing to change over was the stop lever arm that senses the level of ice in the bin.after all this,it didn't work at all.not happy around here.back to filling ice trays
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOEL from LUMBERTON, MS
Parts Used:
W11671282
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
ice will not dispense ice from storage bin to out the door. Auger does not turn
Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffery from MIDLOTHIAN, VA
Parts Used:
W11028221, 12002497
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Empty box sent with no part!!!! No customer service help because of covid
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Angela from Topeka, KS
Parts Used:
WPW10534153
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Refrigerator was missing grille
This grille just snapped into place without the use of tools. Couldn't have been easier. And the delivery was super fast; I ordered online one day and the item arrived the very next day.
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from SEGUIN, TX
Parts Used:
W11291138
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Repaced the right-side door light switch
Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back on and checked the switch. Worked perfectly! Easy job.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Laura from SAINT PETERS, MO
Parts Used:
W11043011
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light in refrigerator burned out
Unscrewed outer cover, unhooked old light's board, hooked up new board, re-installed outer cover. Not really much to this.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jerry from GAMBRILLS, MD
Parts Used:
W11043011
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
the light in the Fridge starting blinking like strobing on and off
I looked up part found parts select, ordered, opened fridge doors put tape over door switch to keep light off, or just hit the turn light off on panel, unscrewed LED light, whick is a led circuit card and not a blub.
snapped it out - snapped new one put retaining screw in , removed tape and WA-LA...
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
dennis from Escondido, CA
Parts Used:
W11043011
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The LED was dim and one of the light is busted..
Unscrew one of the screw with the phillips screwdriver on the far end of the light cover.Then take out the old LED fixture by pushing the two easy snap tabs on the leftside to release it then remove the wire connectors. Then replace it with the new LED. You don't even have to unplug it..????
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Howard from POUGHKEEKPSIE, NY
Parts Used:
WPW10212139
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Had a cracked bin and replaced it with the new one...
Removed as said cracked bin and replaced with one.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from CAPE CORAL, FL
Parts Used:
WPW10714545
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Gasket was old and air leaking into freezer !
Took off old one and just replaced new, very easy and corrected problems!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pamela from MOUNT JULIET, TN
Parts Used:
W11233072, WPW10194032, WPW10194031
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The drawer glides broke
The parts arrived quickly and the repair was so simple it took less than 5 minutes to do, I do however wonder why one screw cost $15.00 though.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
HARRY from FSTRVL TRVOSE, PA
Parts Used:
W11396033
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Catherine from BROOMALL, PA
Parts Used:
W11396033
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WRX735SDBE02
91 - 105 of 275