WRX735SDBE02 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from PALMDALE, CA
- Parts Used:
- WPW10287601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Seal would not stay on, letting cold air out of ice maker - did not make ice.
The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from MELBOURNE, FL
- Parts Used:
- WPW10655368
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Pan is easy part, fan motor assembly is appliance orgami
Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.
This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.
This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from HOUSTON, TX
- Parts Used:
- WPW10212139
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Can't get anyone to send return instructions!!!
I ordered the wrong part for my refrigerator. The refund processed easily. However, the email that I was promised with return instructions has not been sent. I have asked several times about how to return this part and total silence from partselect. I'm ready to throw this replacement bin in the trash.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from PLEASANT VIEW, TN
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch in freezer side got broken
Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from OTSEGO, MI
- Parts Used:
- WPW10300024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Would not make ice.
Removed the whole ice maker unplug one wire harness replaced ice tray with new one.
Very simple.
Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from RADCLIFF, KY
- Parts Used:
- WPW10212139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bin was Cracked/Replacement of Bin
Simple. Just put it on the racks provided in the fridge. The part fit perfectly and took literally 5 seconds to put it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Galen from WASECA, MN
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fresh Food Compartment occasionally going down to 28-30 degrees F
Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from MECHANICSBURG, PA
- Parts Used:
- W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Freezer iced up
Let the ice in the freezer melt while installing P trap drain tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Megan from NORFOLK, VA
- Parts Used:
- 12002497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Boyfriends freezer door wouldn’t shut completely
I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from CONCORD, NH
- Parts Used:
- WPW10194031
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left side pan drawer glide broke at the front screw hole.
Remove broken drawer glide and installed new in less than 15 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- laurie from gold canyon, AZ
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
This is almost embarassing but you asked....
Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PatriciaKendall from ROCHESTER, NY
- Parts Used:
- W11043011
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Main light went out.
First thing was to UNPLUG the frig. Removed the screw in the back of the light. Slid/lifted off the plastic cover took out the light panel and unplugged it. Ordered a new one online and reversed my moves to reinstall the new one ! Not ever having done it before, it went pretty smooth. Easier next time. ??
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from LELAND, NC
- Parts Used:
- WPW10212139
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door shelf cracked
Removed old shelf and installed new shelf. No tools required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from EL PASO, TX
- Parts Used:
- WP67006331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the locking latch to the water filter cover had been broken for a while
Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from Butler, PA
- Parts Used:
- W11043011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
light burned out.
it was so easy to change,and we would recommend your products to anyone.
Was this instruction helpful to you?
Thank you for voting!