BRS62BRBNA00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kay from LA CRESCENTA, CA
- Parts Used:
- WPW10276341
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf for snack drawer
Slide drawer in and fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from JUPITER, FL
- Parts Used:
- WPW10276348
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
needed another shelf
slide right in. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Cedar CVity, UT
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Ice would not come out of the despensor
Pulled out the ice bin and dumpted ice in the sink. Use 1/4 inch nut driver to take out all 1/2 inch screws. Be careful to watch how door spring and holder goes. Pull assembly apart and remove alger. Plastic nut on end of alger has reverse threads, remove it and then remove broken alger drum. Replace with new drum and reassemble in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from COLUMBIA STA, OH
- Parts Used:
- WP2149705
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Lights not working some times
Removed old switch and installed new - but did not solve problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARGARITA from TAMPA, FL
- Parts Used:
- WP2256126
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench (Adjustable), Wrench set
Dispensed water w/ funny looking particles
First the small screws you sent did not fit.I had to cut and mend the old ones (2) to use them.I did purchase a connecting valve tha I used to connect the part of tubing (my name for it) from old one to new one.I was surprides it is working fine.Not bad for a nurse!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maynard5514 from WATERTOWN, WI
- Parts Used:
- WP2180353
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Rubber cover seal old and sticking to the plastic opening - may cause the arm to break
Starting at the bottom, with a flat blade screwdriver pry the front cover off the opening. Unplug the wire connector from the back, remove the cover plate holding the switches and light socket by pushing out on the plastic clips on each side. Use something like a bungie cord to hold it up out of the way. Carefully unsnap the clear plastic ice shoot from the push arm, next carefully unsnap the cover door from the push arm. Clean anything that needs cleaning (CLR works great on hard water deposits)
Install everything in reverse order, the cover door first, ice shoot next, switch plate, plug in the wire connector and snap the outside cover in place.
Install everything in reverse order, the cover door first, ice shoot next, switch plate, plug in the wire connector and snap the outside cover in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mildred from DETROIT, MI
- Parts Used:
- WPW10121138, EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Needed to replace the Refrigerator Water Filter and Water Filter Housing
I watch the video and it was easy as pie 1,2,3 and I was done in know time flat...Thanks for everything I'd recommend these how to do videos to anyone they will save time and money on all your appliance repairs!
Sign; Tony Walker
Sign; Tony Walker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from SPRING HILL, FL
- Parts Used:
- WPW10121138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking water from filter housing
Followed the directions from the video and almost everything went great. The toughest part of the repair was removing the push button cap from the old housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES from SAND ROCK, AL
- Parts Used:
- WPW10121138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
water would not go thru filter
removed 8 screws 3 hose connections and done....hardest thing was getting up from the floor!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yolanda from LA VERGNE, TN
- Parts Used:
- WPW10121138, EDR3RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Well, somehow when I replaced the water filter I turned and don’t suppose to so, it did started licking.
First, I watched the video the sale agent sent it to me. Then I decided to do it myself, I’m a 62 woman that I like to show myself how smart we are as a human being, thanks God! It took me less than 30 minutes to make it work!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chester from Tampa, FL
- Parts Used:
- 4386774, WPW10250570
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Compressor making excessive noise
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Covington, GA
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
my drum was broken and would not put ice down to be used
I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Chandler, AZ
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Auger Busted
Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Removed the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Corona, CA
- Parts Used:
- WPW10329686
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Broken Freezer Door Cams
1. Put pieces of wood under door to support it.
2. Unscrew three screws holding door hinge.
3. Disconnect water line.
4. Unscrew screw holding each cam. One to door and one to hinge.
5 Replace cams.
6. Retrieve plate with threaded holes behind frame that the hinge attaches to.
7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws.
8. Replace all three hinge screws.
9. Connect water line fitting.
10. Remove wood for door support.
11. Check door for smooth movement and strong pressure when closed.
2. Unscrew three screws holding door hinge.
3. Disconnect water line.
4. Unscrew screw holding each cam. One to door and one to hinge.
5 Replace cams.
6. Retrieve plate with threaded holes behind frame that the hinge attaches to.
7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws.
8. Replace all three hinge screws.
9. Connect water line fitting.
10. Remove wood for door support.
11. Check door for smooth movement and strong pressure when closed.
Was this instruction helpful to you?
Thank you for voting!