BRS62BRBNA00 Whirlpool Refrigerator - Instructions

On the bottom of the cover plate are two slots. Insert thin bladed screw driver and pry out gently. Remove electrical connection plate. Remove the old door by removing pin from spring and retaining bracket useing long nose pliers. Install new door kit making sure you use all the parts in the kit. The door buffer is different and the new kit does not require a heater.Install the electrical plate, ice shute and front cover.

took the auger off and baffle replaced the baffle put every thing back together installed back to the freezer tried it out it dont work have to tear into the the motor which works the auger to see if anything else is broke.

Because of the design change of the door hinge it was more difficult to slide the pin into the door and spring. I used an allen wrench to hold it in place on the left side so I could slide the pin in the right hole. Then removed the allen wrench so I could slide the pin all the way. I was very impressed with the time that it took to get the kit. I ordered it about 1:30PM and the following day I had the kit delivered by 6PM. FANTASTIC SERVICE!

I first replaced the water valve, but that did not correct the problem. I then replaced the filter, but still no luck. In the end, it turned out to the the water filter housing was malfunctioning and not letting water through the filter when the filter was installed (it did let water through when the filter was removed, however). I replaced the water filter housing and all worked well once again. The filter housing is not difficult to replace. The hardest part is figuring out how to remove the hoses from the filter. Just push the hose in while holding the plastic ring around the outside, then pull the hose back out.

Emptied door of food jars etc. Used socked on top plate. Removed door and placed on a flat surface. Used socket to take out cam on the bottom of the door. Replaced worn cam. Replaced nylon sleeve on the top of the refrigerator door with needle nose pliers. Placed door in the bootom slot with the new cam in place. Placed top plate in the new nylon sleeve on the door. Replaced screws with socket wrench.

easy -- removed broken shelves and replaced with new ones

I unplugged the fridge, removed the face plate on the front, disconnected the power feeds, unscrewed the electrical panel and moved it out of the way.
I then dismantled and removed the broken part and installed the new part. I was able to use the rest of the existing parts to get the job done.
I put everything back together, and voila! it works great.

Removed ice bucket and discovered the auger drum was broken.

After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.

Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.

Works great now, crushed and cubed ice dispenses thru the door like new.

remove old crisper pan
install new crisper pan
dispose of old crisper pan

the piece fit perfectly and delivery was within a couple days. very satisfied.

Detached the broken ice guide by expandong the opening bewteen the tabs with my hands. Installed the new ice guide and pressed into place. Took about 3 minutes.

This story is less about the repair than the service. On Monday, I removed the meat drawer to give it a quick rinse. Unfortunately, I fumbled the ball getting it back to the fridge, dropped the drawer on the hard stone floor, shattering it.

Instead of calling a repair man or going to the local appliance store, I opened up my macbook, found partselect.com, ordered the part and they had it taken care of in 5 minutes. Two days later, Fed Ex handed me a box with the replacement drawer, and I slide it in. Done. Total time to repair -- 6 minutes.

Sure beats leaving the house!

No repair needed. Just inserted the storage bin onto the hooks provided on the inside of the door.

Replacing the drawer was extremely easy. The refrigerator door need to be completely opened. Drawer slides out very easily and new drawer slides in where old drawer came out. Three minute job, tops.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.