4ET20ZKXBN00 Whirlpool Refrigerator - Instructions

I removed the self brackets and installed new parts, installed the enclosed tape on the bracket and reinstalled into the door.

replaice the end caps with new ones. very easy. happy with partselect.com

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

This problem can be caused by 3 different part failures. Timer, thermostat or heater. After contacting a service repair shop I was told that most often it is the thermostat. The cost of the repair would be at least $115. To much for an old refer. So I ordered the part from Partselect for $33. and put it in myself. Step1 cut the power to the refer. Step2 remove ice maker if you have one. Step3 remove base and back panels in the freezer. Step4 the coils were badly frozen so I used a hair dryer to thaw it out. Would have waited a long time for it to thaw out otherwise. Step5 The thermostat is clipped on to copper tubing next to the coils. Unclip it and cut the wires close to the thermostat. Strip the wires and wire nut the new thermostat. Clip it back on to the copper tubing. Put it all back together and start it up. It's over a week know and no problems. Note: We have whirlpool appliances that are over 16 years old. I have repaired the washer, oven, and now the refer with parts from Partselect. Good company. Always received the correct part within about 3 days from ordering. If you are able to do the work yourself you can save big bucks and keep your appliances running longer. Good Luck

After watching the video it was a snap. Defrosting the freezer took the longest time. I used a hair dryer to melt the ice. Once the freezer compartment was clear of ice the removal and installation were a step by step procedure which the video showed in detail. It's been about a week since I installed the bimetal defrost thermostat and it seems to be working like new. Sure glad I researched this problem on the internet instead of calling a very expensive repairman! Thanks partselect. Com!!!

Pulled up part select video on u-tube. Followed instructions on dissambly of top freezer and found condensor freezing up blocking air from refrigerator. Checked timer to make sure it was good. Next checked continuity on heater to make sure it was good. Last checked bi-metal thermostat for continuity while cold. Found Bi-metal part to be defective (also rubber in top of was popped up which is a sign of a bad part). Simply ordered new part from Part Select, received in 2 days and replaced Bi-metal and melted ice with hair dryer and reassembled freezer. While waiting on part you can still use refrigerator by melting ice so air can get to refrigerator. I put a towel in bottom of freezer to catch water. Greg W. in Ga.

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

First I called my friend Robert in Kissimmee, Fl to have an idea regarding the problem because I had never serviced a fridge before. Then he suggested that I check with PartSelect on the Web. Then PartSelect repair videos showed me everything. I followed step-by-step but the problem persisted. I finally realized that the airflow conduit between the freezer and the fridge was clogged with ice. I then proceeded to remove the ice underneath the coil on the aluminum cover and Bingo. The problem was in fact the ice. Well, I only spent $33 dollars for the non-necessary Bimetal Defrost Thermostat. I learned a great deal from that repair.

took shelf off of freezer, took ice cube maker out, took back panel off changed defrost thermostat.then re-assembled.

I used a socket and ratchet to back out part way the screws holding the seal. There are 4 pieces of metal strips that the screws go through to hold the seal on. Don't remove the screws completely or the plastic panel of the door will fall or come off. Take the new door seal and power it with baby power. This will help make the seal not hang up when you close the door. Now, shake off excess powder outside and then begin to install the seal. Start at the top left or right corner and work across pushing the lip of the seal into the recess of the metal strip. You will want to tighten some of the screws as you go but leave enough looseness to push the seal into the strip's recess. Proceed down each side and the bottom last. I should note that you could remove the door first and you wouldn't have to stand on your head to screw in the bottom of the seal.

followed the video instruction from part select web site

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.

I wasnt about to call Mr Appliance of Bayport NY the last time I called him I got a bill for $72.00 and he told me I needed a new frig. So I paid him then the next day I went to parts select and fixed it myself for about $50.00 But this time it was my Moms frig and the frig side (fresh food side) wasnt getting cold So again I went to parts select and put in a bimetel thermostat and it works perfect now. Im sure I saved a lot of $ and thanks to parts select, They helped me diagnose the problem and make the repair step by step! EASY! Thanks parts select...Garry from long island NY

Had to take everything out and defrost the whole refrigerator dry up and than took back off at bottom and the one covering the Bimetal. The hole was plugged so we took the compressor and blew it and finally got all the ice out before we put on the Bimetal. This is the 4th time we fixed this and I don't know why it won't last longer than 8/9 months. The warrenty is for a year and so far I have gotten 2 refunds thank you!