WRX735SDHZ03 Whirlpool Refrigerator - Instructions

Just plugged it in

This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!

Pried out the old switch and installed the new switch.

I noticed the coils very dusty dirty, tried brushing it clean, ended up blowing it clean. I noticed the condenser fan motor was never turning, I had power, so I ordered a new one. I actual received the evaporator motor, so I had to order the correct one. After changing it, and it started blowing right away. But my refrigerator is still warm. I do not know where the evaporator blower motor is located. I cannot make out from the diagram breakdown. HELP

Took a allen and unscrew the damage door handles and install the new door handles!

followthe instructions in the book that came with the refrigerator

Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.

Watched a couple of videos. Removed left side hinge first, then did the same to the right side hinge. Part was installed in reverse order. Installation took less than 60 seconds.

I popped out the old switch with a screwdriver pressing down the tab on the bottom and unplugged the terminals. Then I plugged in the new switch and popped back into the socket. Piece of cake!

First off, I learned from YTube how to go about figuring out what might be wrong & how to fix it. I watched numerous videos and narrowed it down to the damper as the part to be replaced. I learned how to use the Jazz Board in the fridge to test components & verified the damper wasn't getting signal to open/close. I removed the old damper & put in the new one following what I had seen on the videos. I found a video that had the same type of damper assembly as my fridge & used it to show me how to remove & replace the damper. This was the 2nd part I had to replace to get my fridge up & working. I spent a total of 224.00 on parts and now the fridge is quieter than it's been in years. Finally, if a 66 year old woman can do this, so can you. Just watch YTube & also PartsSelect also has videos also.

Removed old ice maker. Unscrewed unit from slide. Unplugged old wire. Screwed on new unit. Replugged in wire. Slid ice maker back into refrigerator and all worked properly.

Can not do repair. Ordered part 3/30 due to me on 4/1. Today is 4/15 and still no part. I even paid for quicker delivery. Thanks FedEx!!

Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

installed new parts