RT18AKXKQ09 Roper Refrigerator - Instructions

I replaced the cracked crisper drawers with the new ones just by sliding them in the bottom of the refrigerator. This did not solve the problem because one of the drawers was smaller than the other one and left a big space. When I ordered the Crisper Drawers I looked at the part diagram and it looked to me that the drawers were two different sizes and thats what I ordered. I now need to order another large drawer to finish the repair.

install ice maker 2 screws wire harness pluged in done

The bent hinge caused a bad seal which let in air into the freezer, so there was a ton of frost build up. I ordered the parts, and they came in 2 days! I figured what tools I needed, got my wife to help hold things, and in 20 minutes it was like new.

PartsSelect diagrams at their website made it easy to find and order the right part at a reasonable price. I removed the lower glass shelf and frame that supports it. I removed broken track and slipped in the new track and snapped it in place with the orifice at the rear of the track over small peg in the back of the frame. If I had called a regular refrigerator repair man, i'll bet this job would have cost me at least 70 or 80 dollars,

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

I just slipped the new drawer into place. So easy, even a woman can do it! ( I am female!)

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

removed old and installed new compartment door by hand.

Unplug fridge. Remove all items from top shelf of fridge. Remove the two screws holding the control panel to the top of the fridge. Lower unit and unhook it from the rear. Spin freezer knob all the way until you can detach the plastic rod from it. Lower the unit. Unplug the connector of the old timer/defroster. I broke the two plastic pins off that hold the timer to the panel trying to gently remove the clips, but why bother. Remove the timer and replace with new one. Plug it in and reverse procedure to install. Presto!! Cold beer!!!

Using a screwdriver

Removed the old gasket and ran the hard edged lip into the opening behind the door liner. Concerned that the gasket does not seem to be attaching itself to the door well. First put it on the side of the refigerator and it would not adhere enough to support itself. While it closes it just doesn't seem to attach with the magnets in the gasket. These magnetic strips have a weak magnet side and a strong magnet side. I wonder if they put the wrong side facing the door when they assembled it. Counter this with a new gasket for an upright freezer which was twice the length and attached itself firmly to the side wall of the freezer and did not slide down.

Got on floor, pulled broken parts off front of refrigerator. Clipped in new grille. Looks great!

I followed the instructions on the video you provided with my order. Removed the freezer door and used the putty knife to loosen the old gasket and installed the new one. I'm a 77 year old female and if I can do it, so can you.

Installed ice machine components using kit and included instructions. Easy! Ran a copper line from under sink valve to back of refrigerator under the floor. Drilled two holes to run copper line. Plumber turned water off and replaced single valve with a double valve (one line to faucet and the other for the copper line). Installed shut off valve and filter at the other end of copper line. Then stainless hose to refrigerator. Everything went smooth. Double check the factory installed plastic line from the electric valve to the inlet for your freezer. Mine was barely inserted and leaked. I pushed it in all the way and it is fine now... Ice maker works really well! Wish I had done this sooner!

Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.