RT18AKXKQ09 Roper Refrigerator - Instructions

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

Repair man that looked at it said it was the thermostat and that he would order the part. Waited two weeks with no word, so I ordered the part on line, got it the next day and installed it. The only hard part of the installation was getting to the three screws (located vertically in top of refrigerator section) to remove them. Simple three wire clip on changed unit. Total time took about 5 minutes. Refrigerator started cooling when plugged back in. Unfortunately, cooling again stopped within a day, so the original problem was more extensive than just the thermostat (so much for the service call diagnosis). Thoroughly pleased with part ordering, would do it again.

Remove and clean out everything from the freezer and unplug the refrigerator. Take out the wire shelf in the freezer. (The fan motor is behind the back wall of the freezer, SO YOU CAN KEEP THE REFRIGERATOR CLOSED). Pop off the little cover on the center of the plastic shroud. Remove the little screw and carefully remove the plastic shroud. Remove the plastic cover for the optional ice maker on the upper left corner of the back wall. Take out the two screws in the upper corners on the back wall of the freezer and the last two screws holding the fan motor. The fan motor won't drop, remove the back wall and you will see two screws holding the motor mount. Remover those two screws, and pop the bracket out and separate.Take the two rubber motor mounts off the ends of the old motor and install them on the new motor. (Now you will have to cut the wires off the old motor), unplug the little wire harness, strip the ends and crimp on wire connectors to plug them onto your new motor. Its an AC motor so it shouldn't matter which hot goes on which of the two terminals. JUST MAKE SURE THE GROUND IS CORRECT! (After reinstalling the motor, plug in the refrigerator, turn it on before installing the shroud and make sure the fan is blowing outward. If all is correct, turn the refrigerator off, unplug and finish assembling the freezer. I found the new motor seems to run more efficiently than the old one.

Ordered it, received it in due time and it was very easy to replace. As of right now I'm very pleased. Thanks

Unplug pwr cord ..then chk voltage on refrigerator...go inside refrigerator to upper unit where light is and lower unit dwn bye removing the screw then look for thermostat it's right inside ..remove to 3 wires then install new thermostat the same way....plug unit in to power rotate thermostat cooling setting and listen for compressor to tune on. If all goes well the refrigerator should cycle. ....if not change out control board. Good luck and have fun.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Original handle had broken, and super glue wasn't holding any longer. It's just three screws, two up top and one on the bottom that hold the handle on. The fridge and thus the handle comes in three colors (white, biscuit ,and black) I had to email customer service to find out that white is part no PS330447. I got an absurdly fast reply to my question given it was a Saturday afternoon, so that made it easy.

The majority of the repair time was spent moving the items in the refrigerator off the glass top under which the track was to be placed. After that, the track was a cinch to put in its place (it's pretty idiot-proof). Perhaps the track wouldn't need replacement if it were made of something stronger than plastic, but I felt pretty handy doing this for my wife, and she's glad to have the hydrator drawers back in proper operation.

Remove the cover off of the compressor connection box,,,pull the old start-device,replace it with the new one,and there it is running just fine. The amps droped to normal and the compressor is not over heating any more.Nothing to it. 15 to 20 min. Time to do the repairs

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Grat help on the phone. We saw repair on YouTube. my wife and I worked it together. It was child's play!! It went beautifully. we were able to "chill out" with ice aplenty!!Thanks...eric

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Very simple fix, remove 3 screws, two connectors to the old switch

Very easy to install