MSX24DRAAD RCA Refrigerator - Instructions

Shut off water and disconnected at factory joint at bottom hinge. Unplugged the electrical at the top hinge. Removed the door and installed new bottom hinge and cam assembly. Reinstalled the door and hooked water and electric back up. Part worked fine.

removed old parts and installed new. went smooth

When it was discovered there was a cooling problem in the refrigerator, I went to parts select web site and went through the troubleshooting section. Then I tested the defrost timer and the defrost element as directed by the web site. I then found out doing this, that is was the defrost timer. I ordered the part online and it was delivered THE NEXT DAY! I removed the bottom panel of the fridge, removed the screw holding the old timer, removed the wires, and reversed the procedure to install the new one. It has been 1 week, and everything is working great. Thank you PartSelect.
I have since then recommended you to a relative who was having the same problem. Thanks again.

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

It was very simple, took out the slide rails and took a screwdriver and assembled. My wife was very pleased to have these drawers in working order once again.

I removed all items from area of refrigerator. I removed the drawers. I unscrewed the broken slide rail. Upper drawer had left side broken. Lower drawer had right side broken. I simply screwed the new slide rail in. The glass shelf didn't fit, so I took a pair of needle nose pliers and broke off a tiny piece on the slide rail that was preventing the glass from dropping in. (I checked the old one first and could see the same thing had been done) I screwed each rail in and dropped the glass shelf back in. (The lower shelf was broken and I ordered a replacement at the same time as the broken rails. I put the glass into the plastic holder of the old (broken) shelf and slipped it back in. Very easy. I'm a housewife not a repairman. I saved a few dollars on a house call.

Disassembled front door/cover (3 screws), then removed deflection door assy, (4 1/4" nuts), CArefully and methodically removed C Clip and grinder teeth...Be careful with this step to document/remeber how to re-assemble! Auger repleced then reverse steps...
All in all, not too bad, but you can easily screw up the teeth re-assembly.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long

Removed old hinge assembly, bolted on new assembly-door shut like new

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

Repaired with the help of You Tube videos. To repair: remove door (note! the door can be removed without pulling the dishwasher out, or disconnecting spring cables). To remove the door insert allen wrench in holes under door to hold the door in the remove/ install position. separate the inner and outer door (easily done) then remove and replace the User interface board. The hardest part was locating the holes to insert the allen wrenches (or anything similar) in to. Dishwasher worked after repair. In my case the dishwasher would come back to life for a short period if I turned the power off, and back on. I read somewhere that was a symptom of the bad UI board. I was lucky because that was the problem.

Turn of power to fridge. Removed all shelving in freezer section. Unscrewed back panel from freezer area. Removed old defrost term t-stat from top of evaporator coil assembly. Cut existing two wire leads, spliced in new T stat wires. sealed wire splices from water egress and clipped new t-stat in same position as old one. Reassembled rear panel, installed shelves. Turned power back on.That's it.

Remove three screws insert part; manually checked out drive and waited for ice to buildup and it worked like new.

Since the cam riser was obviously broken I obtained a replacement.
It also broke. The door hinge cam needed to be replaced also.
To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam.
Replace in reverse order.
Be sure to inspect all parts and order all required.