GS2325GEKW Maytag Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from MT PLEASANT, SC
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge running warm
The fridge would occasionally run warm, requiring me to turn it off and defrost the evap coils in the freezer. I found an online video that demonstrated the entire process of replacing the control board. The fridge model in the video was different than mine, so it took some time to figure out how to remove the panel. Once that was done, the rest was easy. The only tool required was a flat-head screwdriver that was used to push in the tabs holding the panel in place. The circuit board took more effort to split in two than I had realized, and I had to be careful not to bend any of the components on its surface. The whole process took less than 30 minutes, and the fridge is working properly now..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from ALEXANDRIA, VA
- Parts Used:
- WPB5705307
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
Ice from icemaker taste metallic; new ice maker directly from box
I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from FSTRVL TRVOSE, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from ST CLR SHORES, MI
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
needed to replace water filter
unscrewed old filter, screwed in new....good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEFF from SEATTLE, WA
- Parts Used:
- 12002355
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
FREEZER WOULD NOT DEFROST.
I initially tested the heating element and defrost thermostat using an ohm meter. the defrost thermostat was incased in ice, so I replaced it first. The refridgerator worked for about a week and then froze up again. I then replaced the thermistor and the unit is working as designed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from DUNNELLON, FL
- Parts Used:
- WP12665101, WP12562701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Icemaker chute door seal was deteriorated
Watched a Utube video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oro Valley, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from New Johnsonville, TN
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch broke.
Couldn't figure out how to get the old one out till I saw the new one.Pop the old one out slide the 2 wires on the new one pop it back in place,good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Pensacola, FL
- Parts Used:
- W11291138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch broke
Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROSE MARY from MARYSVILLE, WA
- Parts Used:
- WPW10152975
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Original Armwire Had Fallen Off In The Ice Bin And Got Bent. That Is Why I Ordered The New Armwire Assy.
I removed ice bin and cover that sits ontop of the icemaker. I inserted the longer end of armwire assy first in the front part of the icemaker arm until it clicked in place then inserted the shorter end in the back side of icemaker arm and pressed until it went into the hole all the way through. This was very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Minneola, FL
- Parts Used:
- R0181181
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The fridge lower hinge mechanism which assists door closing broke
Removed the top hinge cover with Philips screwdriver. Removed the three bolts holding the top hinge in place. Removed the top hinge, and lifted the door off the remains of the lower hinge. Unbolted the remnants of the lower hinge closure mechanism and replaced it with the new set. Reassembled the door on the lower hinge, and then replaced and bolted back on the top hinge. Door back to full working order in less than fifteen minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oswald from Miami, FL
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice Carrier End Cap
Removed Ice carrier and diassembled the Ice carrier with a socket set. Four screws, cap came right off. Placed the new one on and finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Lancaster, SC
- Parts Used:
- WP67002052
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Plastic wheel in icemaker broke
I removed the ice tray from the freeze. Turn over and remove screws holding the face plate on. Remove the 4 screws holding the crushing mechanism in place. Pull the entire mechanism out and remove the nut holding the blades together. Remember the alignment of the blades. Remove blades and then the pastic crush wheel. Replace in reverse order. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Merrimack, NH
- Parts Used:
- WP67006006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear of bucket tilted down holder broken
First I removed the ice bucket from freezer removed 2 screws from the front that hold ice auger in place. Slid ice bucket out replaced new bucket replaced 2 screws returned to freezer.
Was this instruction helpful to you?
Thank you for voting!