GZ2626GEKW13 Maytag Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Matthew from Pensacola, FL
- Parts Used:
- W11291138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch broke
Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oro Valley, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROSE MARY from MARYSVILLE, WA
- Parts Used:
- WPW10152975
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Original Armwire Had Fallen Off In The Ice Bin And Got Bent. That Is Why I Ordered The New Armwire Assy.
I removed ice bin and cover that sits ontop of the icemaker. I inserted the longer end of armwire assy first in the front part of the icemaker arm until it clicked in place then inserted the shorter end in the back side of icemaker arm and pressed until it went into the hole all the way through. This was very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Merrimack, NH
- Parts Used:
- WP67006006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear of bucket tilted down holder broken
First I removed the ice bucket from freezer removed 2 screws from the front that hold ice auger in place. Slid ice bucket out replaced new bucket replaced 2 screws returned to freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Montoursville, PA
- Parts Used:
- WP12740302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice would not come through door, troubleshot and determined bale mechanism wasn't turning properly.
Removed old agitator unit - 4 nut-head screws removed, and installed new agitator and screws aligned easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oswald from Miami, FL
- Parts Used:
- WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice Carrier End Cap
Removed Ice carrier and diassembled the Ice carrier with a socket set. Four screws, cap came right off. Placed the new one on and finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Lancaster, SC
- Parts Used:
- WP67002052
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Plastic wheel in icemaker broke
I removed the ice tray from the freeze. Turn over and remove screws holding the face plate on. Remove the 4 screws holding the crushing mechanism in place. Pull the entire mechanism out and remove the nut holding the blades together. Remember the alignment of the blades. Remove blades and then the pastic crush wheel. Replace in reverse order. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary L. from Millsboro,, DE
- Parts Used:
- WP627843
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Whittier, CA
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Replace ice & water Filter
Open and remove lower cover on filter holder by opening tabs that hold lower cover and remove lower cover.
Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.
Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.
Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.
Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ketchikan, AK
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Low Water Pressure
Followed directions on filter unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Noank, CT
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacing filter
Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from CORSICANA, TX
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator light stopped working
Followed the instructions in the video provided via email from Partselect
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kerry from DE PERE, WI
- Parts Used:
- WPD7749401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
End Cap was broken and ice would not dispense.
Ridiculous how easy it was, REALLY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from SAINT ALBANS, VT
- Parts Used:
- WPA3223101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
Was this instruction helpful to you?
Thank you for voting!