Models > GZ2626GEKB13 > Instructions

GZ2626GEKB13 Maytag Refrigerator - Instructions

Jump to:

All Instructions for the GZ2626GEKB13
61 - 75 of 202
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Matthew from Pensacola, FL
Parts Used:
W11291138
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light switch broke
Popped out the old light switch with a butter knife from the bottom first, disconnected the plug in. Install was just the reverse. Super easy fix
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from Oro Valley, AZ
Parts Used:
W11396033
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROSE MARY from MARYSVILLE, WA
Parts Used:
WPW10152975
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
My Original Armwire Had Fallen Off In The Ice Bin And Got Bent. That Is Why I Ordered The New Armwire Assy.
I removed ice bin and cover that sits ontop of the icemaker. I inserted the longer end of armwire assy first in the front part of the icemaker arm until it clicked in place then inserted the shorter end in the back side of icemaker arm and pressed until it went into the hole all the way through. This was very easy to install.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barry from Merrimack, NH
Parts Used:
WP67006006
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Rear of bucket tilted down holder broken
First I removed the ice bucket from freezer removed 2 screws from the front that hold ice auger in place. Slid ice bucket out replaced new bucket replaced 2 screws returned to freezer.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Howard from Montoursville, PA
Parts Used:
WP12740302
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Ice would not come through door, troubleshot and determined bale mechanism wasn't turning properly.
Removed old agitator unit - 4 nut-head screws removed, and installed new agitator and screws aligned easily.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Oswald from Miami, FL
Parts Used:
WPD7749401
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Ice Carrier End Cap
Removed Ice carrier and diassembled the Ice carrier with a socket set. Four screws, cap came right off. Placed the new one on and finished.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bryan from Lancaster, SC
Parts Used:
WP67002052
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Plastic wheel in icemaker broke
I removed the ice tray from the freeze. Turn over and remove screws holding the face plate on. Remove the 4 screws holding the crushing mechanism in place. Pull the entire mechanism out and remove the nut holding the blades together. Remember the alignment of the blades. Remove blades and then the pastic crush wheel. Replace in reverse order. Very easy.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary L. from Millsboro,, DE
Parts Used:
WP627843
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
16 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Whittier, CA
Parts Used:
EDR4RXD1
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Replace ice & water Filter
Open and remove lower cover on filter holder by opening tabs that hold lower cover and remove lower cover.

Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.

Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Ketchikan, AK
Parts Used:
EDR4RXD1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Low Water Pressure
Followed directions on filter unit
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eric from Noank, CT
Parts Used:
EDR4RXD1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Replacing filter
Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kerry from DE PERE, WI
Parts Used:
WPD7749401
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
End Cap was broken and ice would not dispense.
Ridiculous how easy it was, REALLY!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from SAINT ALBANS, VT
Parts Used:
WPA3223101
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carlton from CHICAGO, IL
Parts Used:
W11396033
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Randy from CLARINDA, IA
Parts Used:
WP67006006
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Lip of ice bucket kept breaking off and pieces would jam dispenser.
Took longer to pull fridge out and push back than to replace bucket. Pull bucket and dispenser out . Carefully unsnap plastic front cover and access door from bucket. Loosen two hex screws that attach bucket to dispenser. Auger assembly comes loose. Just reinstall auger and screws then carefully snap front back on. Slide unit back in freezer.Push fridge back in place. Take a beer out of fridge. Drink it and pat yourself on the back!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GZ2626GEKB13
61 - 75 of 202