GC2227HEKS Maytag Refrigerator - Instructions

I removed the front cover--just popped off with no trouble. Removed 2 screws at the bottom. Slid the broken part out and put the new one in place. Put in the two screws, replaced the fron cover AND Done!!!
BTW I am a 65 year old woman and the icemaker is like new.

Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!

While ordering the assembly, I had thought that the ice bucket was included but it wasn't. So I ordered the ice bucket afterwards. Maybe a little more clarity as far as what parts come in the whole assembly would save some time. All in all, the agitator was very easy to install, along with the ice bucket. After securing the agitator to the existing assembly with two screws, the ice bucket slipped right into place. Easy to install.

Had to disassemble ice maker to install part. . .

As the prior stories mentioned, this was a fairly easy fix to a nagging problem. Heck, we almost bought a new refer over this, cuz the door would keep popping open.

Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I didn't do that!)

With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.

Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!

Greg

By sliding athin screwdriver blade down the side of the old switch the expasion prong that hold the switch in place was compressed enough to allow the switch to come out easlily. Plugged in new swithc and snapped in place. Plugged the refrigerator back in and light has worked great sense!

called jennair described the problem no help? they thought it might be the power board but it was not .. I put inthe new board same problem..so there is only one other component left the key pad!!! no thanks to the jennair I found the problem and fixed it....

Snapped into place with the attached clips. Could not be easier. Really great service from PartSelect--got here faster than I expected. This was a great service--would recommend to everyone!

I pulled off the plastic shield from the front of the ice bucket. This exposed the two screws that I needed to remove to disassemble the ice crusher mechanism. Once the screws were removed, I was able to remove the helix and replace the end cap that was broken and place it in the new ice bucket. If I would have known it was this easy, I would have changed this out a year ago, instead of doing without crushed ice through the door for so long. Thanks PartSelect. com! I am a customer for life!

Firts checked the parts received werer correct for the repair and the correct part numbers ordered. Then removed the ice bucket with the auger in bottom. Emptied ice from original bucket auger assembly. Checked out the removeal of the face cover for the bucket auger and removed it from clips that held it in place. Checked the specifications of the old ice bucket compaired to the new parts. Installed the aurger assembly into the new ice bucket and removed the two screws from the old unit to use in secure the auger assembly in the new bucket. The only tool needed was a 1/4 inch nut driver. Installed the face place on the new ice bucket auger assembly and tested the fit in the freezer. Ran test of the auger assembly without ice to ck for any misinstlled parts. Refilled the ice bucket with ice and tested with ice to complete the repair.

First, I removed the bucket and drained all the ice from it. Then I took the ice bucket out and lifted off the cover of it which exposed the teeth that grind up the ice. I then removed these in succession and placed on my table so I could make sure I put back together appropriately. Once I had the bucket with everything off of it, I replaced and threaded the auger back through it so I could attach the end cap to it. Once that was in place, I put the parts back on the way I took them off. It really was a painless process and saved a ton of money versus calling a repair person. Definitely will use the service again. Very prompt delivery as had the parts 2-3 days after ordered. Well done.

One day when i went to get ice our ice maker started to jam. When i took it out i noticed that the metal arm that turns was out of position and blocked due to the End cap being out of place. I then put it back in place and it happened again. The bucket cracked due to the pressure caused by the ice been . The only problem that i have now is that when i hit cubed ice, crushed ice comes out...and when i hit crushed ice, cubed ice comes out. The installation and swapping of parts wasw really easy. Partselect has great breakdown diagrams so if you get lost u can turn to them.

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was available. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.

Unscrew filter. Screw on filter bypass