KFIS25XVMS00 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kevin from Spring, TX
- Parts Used:
- 8201515
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Old motor was not resetting back to proper position halting ice production.
Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Gainesville, FL
- Parts Used:
- WPW10534153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old one was broken and kept falling off. Very annoying
Snapped new cover on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from JACKSONVILLE, FL
- Parts Used:
- WPW10714545
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice buildup around freezer door gasket
Replaced with new gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MEMPHIS, TN
- Parts Used:
- WPW10662129, WPW10197428
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Clicking noise, getting louder. Then stopped cooling
1. Empty your fridge. Lighter is easier to move and this is the hardest step in the fix. 2. Move your fridge so you can get behind it. Unplug the fridge. 3. Use a 1/4in nut driver to remove the screws from the back panel. 4. Remove the back panel. 5. Locate the compressor (big cylinder, usually black) and find the capacitor (PS11757023) and start dev (PS11750123) plugged into the side of the compressor. 6. There is a steel spring restraint wire, remove this. 7. Remove the pin connector (plastic w/ wires going to it) by pressing and pulling gently. Remove the old capacitor and start dev. 8. Assemble the new capacitor and start dev to each other. 9. Plug the pin connector into the new replacement components. 10. Align the start dev to the location of the old components. There is a 3 pin outlet that aligns to the 3 plug holes on the start dev. Align the plug then push gently but firmly to seat the components back together. 11. Reinstall the restraint wire. 12. Reinstall the pack panel. 13. Put your refrigerator back in place and load it up! You're all done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommy N from Tipton, IN
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Pin for lid broke 2 Liter of pop fill on it
Removed drawers and glass top and support bars Two screws on slid bar two screws on end cap, Make sure you take time to remove air control it has two pivot points with small taps.
Then just replace parts as you had taken off very easy.
Then just replace parts as you had taken off very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Richardson, TX
- Parts Used:
- WPW10326469, WP67003854
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Parts broke due to overloading crisper trays
Wife learned you can overload the cheese and fresh veggie trays and the plastic rails broke. Repair required removing parts from the old crisper frame -- no experience and no instructions. Had to study broken part and figure out how to remove parts. Released catches with a knife and, by trial and error, figured out how to install rescued components on new crisper frame with minor damage and frustration.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenny from PHOENIX, AZ
- Parts Used:
- W11415785
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
spraying water from the connection on top of fridge
just like the video showed, removed the cover parts inside the fridge, disconnected the water tube inside and pulled out from the top of fridge, then inserted new water tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from South Lebanon, OH
- Parts Used:
- WPW10326469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tab on end broke off allow crispers to fall off rail.
lift glass, slide new rail in replace glass. 2 min repair.
Was this instruction helpful to you?
Thank you for voting!
The ice maker stopped working
First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.
This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.
This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myrna from El Paso, TX
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The LH End Cap hinge stud had broken...
Removed the crisper drawers (pull out, then up & out), remove the glass shelf above the "pantry", remove the pantry door (easy because hinge stud was broken), then remove the pantry drawer. Use 1/4" nut driver to remove the broken LH End Cap...it pulls up and out. With the phillips screwdriver, remove/replace the steel rail for the drawer action to the new part. Replace in reverse order (after your neat freak SO cleans everything!).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from PLEASANT VIEW, TN
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch in freezer side got broken
Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from GREENFIELD, IN
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Remove the water filter to install the bypass cap
Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Long Valley, NJ
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Six months in use time to replace the filter
It is simple, unscrew the old screw in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Murphy, NC
- Parts Used:
- WP67003639
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Right hand door would not auto close.
Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.
But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.
But this did not fix the problem. Will have to remove the door and inspect the inside of the door's lower hinge assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Spokane Valley, WA
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace water filter
pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh
Was this instruction helpful to you?
Thank you for voting!