KTRS21KDBL04 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- STANLEY from OAKLAND, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rocker switch broke off
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from woodland hills, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
you have to turn it off and on to run.
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Jefferson Hills, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Internal light did not come on each time the door was opened.
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from New Bern, NC
- Parts Used:
- 4387535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
After Hurricane Irene refrigeration compressore did not start
Followed the directions. Installation was quick. Took loner to put the covers back on and push the applicance back in position than the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Flagstaff, AZ
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The light went out
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Destin, FL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch would not work
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Billings, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
non-functioning refrigerator lite switch
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Dunmore, PA
- Parts Used:
- W11745278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
replace hinge bracket on fridge door
taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Conroe, TX
- Parts Used:
- 4387535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Starting relay went out
Forty years ago I serviced air conditioners and all kinds of refrigeration. At that time starting relays were electro mechanical, I hadn’t looked under a refrigerator in a lot of years and was surprised to find out that the new relays were solid state. The defective one had a bunch of broken pieces floating around in the case. I jury rigged a starting cord and confirmed that the compressor would start and looked at running current for thirty or so seconds. I ordered a new relay kit and it worked just right. I’m seventy five years old and it takes me longer to get up off the floor than it took to replace the parts. Your delivery was first rate the parts got here before I finished doing the paint touch-up on the door under the ice maker/water dispenser. Fed ex was easily three to five days faster than the brown truck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Boxborough, MA
- Parts Used:
- 4387535
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
change relay
unplugged relay and plugged in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Nova, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Arlington, MA
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRUCE from KRUM, TX
- Parts Used:
- W10822259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Unit Running Hot
Insalled fan motor,problem went away. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Woodacre, CA
- Parts Used:
- 2182338
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
defrost tray & drain, pluged with ice in freezer section
poured boiling hot water into drain; removed most ice with hair dryer. Clips(2) positions the defrost tray & drain under the freezer condenser. A "home-made" coil of 18g copper wire inserted into the drain hole, & secured to the defrost heater further prevents the drain from iceing shut!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Mission Viejo, CA
- Parts Used:
- W10822259
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Fan motor making awful noise, not turning very fast
Fan was barely rotating. So unplugged, removed back cover, removed fan and motor from frame work. Removed fan blade from motor shaft. Spun motor shaft which seemed fine. Pryed off back cover of motor to find a large but dry felt washer and a helical capillery slot formed into the motor shaft for carring oil from felt washer to the bearings. Added 30 wt motor oil and some 3in1 oil to felt and reassembled motor, fan and frame work. Plugged in power chord after getting rid of dust and dog hear on coils and is working like new.
Was this instruction helpful to you?
Thank you for voting!