59650013100 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linford from Cedarville, NJ
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker would not fill with water.
Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Madison, AL
- Parts Used:
- WP67005959, WP12740302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Auger not dispensing ice, motor working properly
Firts checked the parts received werer correct for the repair and the correct part numbers ordered. Then removed the ice bucket with the auger in bottom. Emptied ice from original bucket auger assembly. Checked out the removeal of the face cover for the bucket auger and removed it from clips that held it in place. Checked the specifications of the old ice bucket compaired to the new parts. Installed the aurger assembly into the new ice bucket and removed the two screws from the old unit to use in secure the auger assembly in the new bucket. The only tool needed was a 1/4 inch nut driver. Installed the face place on the new ice bucket auger assembly and tested the fit in the freezer. Ran test of the auger assembly without ice to ck for any misinstlled parts. Refilled the ice bucket with ice and tested with ice to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Monroe, WA
- Parts Used:
- WP12555902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator and freezer was not cooling. The compressor would not stay running. When the compressor kicked on it would only run for a few seconds and got warm real quickly. I replaced both the overload relay combination and the running capacitor. Don't know what the problem is. I thought for sure t
disconnected wire connections, pulled old overload relay and running capacitor out like a plug and plug in the new one then reconnected the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Hanover, MA
- Parts Used:
- WP67006506
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Power cord was cut
I removed the 5/16 inch hex head nuts holding the rear access panel where the power cord was connected. Once removed, I released the Molex plug and ground wire. I connected the new cord, screwed in the ground and installed the rear panel. Having the exact OEM part made the job quick and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from MANKATO, MN
- Parts Used:
- WP67001503, W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light switch had broken off and so the light would not go on when the door was opened. Vegetable crisper drawer had broken along the sides.
We unplugged the refrigerator, used a knife to pry out the old switch. Cut the extra prong off of the new switch and connected the switch to the wire connectors. Slid the switch back into place plugged the refrigerator back into the outlet and . . . . . . Wah, lah, the light and switch worked again. We washed and then simply slid the vegetable crisper into the holder and replaced the one that had broken. This was a really great experience and it was quick and easy to fix on our own.!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Loreauville, LA
- Parts Used:
- WP67005959, WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken ice bucket and broken helix end cap.
I pulled off the plastic shield from the front of the ice bucket. This exposed the two screws that I needed to remove to disassemble the ice crusher mechanism. Once the screws were removed, I was able to remove the helix and replace the end cap that was broken and place it in the new ice bucket. If I would have known it was this easy, I would have changed this out a year ago, instead of doing without crushed ice through the door for so long. Thanks PartSelect. com! I am a customer for life!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Bronxville, NY
- Parts Used:
- WP67002224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dog ate toe grille
Snapped into place with the attached clips. Could not be easier. Really great service from PartSelect--got here faster than I expected. This was a great service--would recommend to everyone!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Cupertino, CA
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The ice maker stopped making ice.
I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from MUNDELEIN, IL
- Parts Used:
- W11395888
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Did not need filter
Unscrew filter. Screw on filter bypass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amol from Missouri City, TX
- Parts Used:
- WP67005959, WPD7749401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker started to jam
One day when i went to get ice our ice maker started to jam. When i took it out i noticed that the metal arm that turns was out of position and blocked due to the End cap being out of place. I then put it back in place and it happened again. The bucket cracked due to the pressure caused by the ice been . The only problem that i have now is that when i hit cubed ice, crushed ice comes out...and when i hit crushed ice, cubed ice comes out. The installation and swapping of parts wasw really easy. Partselect has great breakdown diagrams so if you get lost u can turn to them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Windsor, CA
- Parts Used:
- 833697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
refrigerator not cooling properly
Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHARON from CEDAR RAPIDS, IA
- Parts Used:
- WP67005716, R0181181
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Uneven doors, freezer door had to be pushed to be sure it was shut
Followed video and used vaseline to lube as suggested by other review.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from New Lenox, IL
- Parts Used:
- WP67005959
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice tray track was broken- hanging down with weight
Took ice tray out, removed plastic decorative cover, remove the four nuts under the cover, slide out the ice auger assembly as one piece. do not take auger assembly apart. I repaired mine once, difficult without a schematic picture, many parts, replaced everything back into the new ice bucket. Easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Florance, MT
- Parts Used:
- WPD7749401
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Auger in the ice tray not turning
Removed ice container, replaced end cap that holds Auger shaft that connects to shaft that turns the Auger. End cap plastic nubs wear where it makes contact to the turning stub. Removing a few screws on the front of ice container allows the Auger shaft to slide forward and away from the end cap. Maneuver end cap from shaft, replace using same maneuver and that is it.
Pretty easy, even for a novice like me. A $6.00 end cap verses the whole assembly at around $70.00
I'm pleased.......
Pretty easy, even for a novice like me. A $6.00 end cap verses the whole assembly at around $70.00
I'm pleased.......
Was this instruction helpful to you?
Thank you for voting!