59677532600 Kenmore Refrigerator - Instructions

Removed the back cover for the HV Board. Unplugged the cables from the old board, put the new board in the same exact way, connected the cables. Put the back cover back on. The hardest part was the programming. You may need to read it again in order to figure it out, but not too difficult. Face it there are only so many buttons, eventually you will go "AH-HA" ! I saved myself around $250! I will most definately use this site if I have other appliances that do not work! You guys rock!

~Lisa~

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

It was a very simple operation to replace the parts and required essentially no tools, just a small screwdriver to pry up a tab for removal of the chanel on the front edge of the frame. This chanel had to be removed from the old crisper frame and installed in the new one. In addition the crisper control" had to be popped out of the old frame and into the new frame. Most of my time was spent cleaning.

I removed the 5/16 inch hex head nuts holding the rear access panel where the power cord was connected. Once removed, I released the Molex plug and ground wire. I connected the new cord, screwed in the ground and installed the rear panel. Having the exact OEM part made the job quick and easy.

Unplug Refrigerator access panel in the rear unscrews- disconnect the wire harness from circuit board- remove board (snaps out). Insert new board ,attach wires close access panel. Plug refrigerator in. reprogram fridge code with ice maker controls code is on label with model number and s/n number.

There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.

Removed the door and replaced the broken door closure bushing. I had courteous help and responce from Parts Select people. Excelent turn around time on parts delivery.

Unscrew filter. Screw on filter bypass

First it was critical to have gone on-line to see that many other people have had the EXACT problem with their Maytag refrig. It went crazy at 830pm the Wed before Thanksgiving! There would have been NO WAY that we could have had that repaired with the holiday! I went to Parts Select and ordered the part that very night ( they were open and taking customer service calls until 11p EST). They had the part to us first thing Monday morning!

The installation was simple and they provided perfect instructions as to the programming of the code.

I cant believe that Maytag has not dome some sort of recall on the control board for these refrigerators. When we looked at the old one, there was moisture on the plastic panel and the 2 capacitors were corroded and bulging. We are going to try and get those replaced, so we have a spare board.

It was a whole lot cheaper to replace the board, and many would just resort to paying a repair bill of >$500.00 for the cost of a $200.00 part and about 15 minutes. You dont have to be an electronics major to fix this either!

This whole thing saved us well over $2500.00, as we are not buying a new refrigerator. I will say that we will never buy another Maytag at this point! All beware and might want to have an extra control board handy!

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars

proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.

Receive the parts. Review the video. Thought I can do this got down to the screw and I didn’t have is a ratchet small enough to remove the screw so I had to call D.O.C appliances to do the install Michael was here less than 15 minutes

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Very simple--Just remove all drawers, remove old end cap, remove slider from old end cap and put on new one. Screw on new end cap and replace drawers. Took about 10 minutes.

Instructions were great five minutes to remove and replace fan....Thank You............ saved big money