59677532600 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken drawer lid connector
I removed and replaced the right pantry end cap, as well as the drawer lid.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank I. from FREMONT, CA
- Parts Used:
- WPW10326469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Center rail broke.
Removed the top glass above the vegetable drawers and slipped the center rail in place. And I would like to add that I would do business with this site again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from San Diego, CA
- Parts Used:
- W10613606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator compressor not run
Replaced the relay and capacitor it runs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WATERBURY, CT
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Pin for drawer lid broke off
Empty drawer and take out . remove glass shelf and front and rear shelf braces. remove 2 screws holding pantry end cap to fridge. remove rear bracket by unsnapping clips. remove temp control arm. and reattach to new end cap. reinstall rear bracket to fridge and align end cap, align screws and tighten. reinstall drawers and shelf brackets. replace glass shelf. and reattach lid to brackets. Open beer and enjoy success.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arja L. from NEWBURY PARK, CA
- Parts Used:
- WP67006331
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Snap on cover broke
Saw U tube instrctions how to install and it was easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Megan from NORFOLK, VA
- Parts Used:
- 12002497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Boyfriends freezer door wouldn’t shut completely
I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Nesconset, NY
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Plastic food door hinge broke
Removed the food bins and lower shelf. Unscrewed the end cap. Removed the drawer hinge. Re-installed hing on new end cap. Installed the new end cap. Re-installed drawers and shelf. DONE!
Great graphics on the website helped to correctly idenitfy the required part. Part arrived quickly and well packed. One of the easiest transactions ever!
Great graphics on the website helped to correctly idenitfy the required part. Part arrived quickly and well packed. One of the easiest transactions ever!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Flagstaff, AZ
- Parts Used:
- W10890094
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
replaced HV control board on refrigerator
took off plate in back, plastic cover, unplugged cables, changed out board held by clips. plugged cables into new board. Plugged refrigerator back in. entered refrigerator code into door of refrigerator using temerature controls. Regrigerator started cooling. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gretchen from Fountain Hills, AZ
- Parts Used:
- W11266639
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Chiller Frame anchors broke off so door wouldn't stay on
Simply fit the frame onto the back piece and lined up all of the anchoring plastic hooks to reattach. I had some minor difficulty in navigating the website but the customer service agent was very helpful and assisted me in purchasing the correct part. Thanks! Gretchen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alex from north lauderdale, FL
- Parts Used:
- W10890094
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice dispenser flapping and digital board flashing
replaced the high voltage board in the back of the refrigerator, then followed the instructions to program the board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- laurie from gold canyon, AZ
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
This is almost embarassing but you asked....
Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!
Was this instruction helpful to you?
Thank you for voting!
broken nipple/hungry kids
Took bottom 2 shelves out. 2 screws held assembly in to main cabin. Remove them then 2 additional screws held drawer bracket in place. Easy yet patience and finesse is needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from PALMDALE, CA
- Parts Used:
- WPW10287601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Seal would not stay on, letting cold air out of ice maker - did not make ice.
The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from LAKE CHARLES, LA
- Parts Used:
- W11447232
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the light bulbs went out on my Whirlpool refrigerator.
I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.
It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.
It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from ALIQUIPPA, PA
- Parts Used:
- W11396037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket torn
Pulled old gasket off door put new one in channel on door pushed gasket in channel less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!