59679242013 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from VINEYARD HVN, MA
- Parts Used:
- W10827914
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Drawer door broke
It snapped into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from SCOTTVILLE, MI
- Parts Used:
- W10882923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Unplug and remove existing wiring harness and old ice maker if need to.
Got lucky ordered new ice maker then current one started working again ???????
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from COAL VALLEY, IL
- Parts Used:
- WP67006878
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
The old shelf shattered when we tried to clean it
Just slipped it in. I think it's a very poor design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from SAMMAMISH, WA
- Parts Used:
- WP12227303WD
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My refrigerator vegetable bins were sagging when I placed veggies in it.
I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeannette from MESA, AZ
- Parts Used:
- W10882923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
ice maker wouldn't work
The repair went well. Before I ordered this ice tray assemble, I replaced the water inlet valve thinking that was the problem. The new ice tray came with 2 new wiring harnesses. It wasn't hard to see which one was needed for the new system. Changing the tray out was not hard at all nor was the new electrical harness. The only problem was the inlet valve sent too much water into the ice tray. After seeing the ice tray leaking, I removed it again to see why. The only thing I could come up with was too much water was being put into the ice tray. I had the old inlet valve and reinstalled it and the ice maker has worked flawlessly ever since. There was nothing wrong with the old inlet valve only the ice tray assembly.
So all good and doing a great job once again.
So all good and doing a great job once again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dalton from BEAUFORT, NC
- Parts Used:
- W11197396
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
peg that swings the pantry door open and closed was broken off
watched partsselect video and simply followed the directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from SOUTH ST PAUL, MN
- Parts Used:
- WPW10534161
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Clips on old toe kick plate were broken on one side. Would not stay on
Took the new kick plate out of the box. Snapped it into position. I have had a repairman for this refrigerator before. I would rather repair an appliance than buy a new one. I'm very proud that I thought to get a replacement part myself instead of calling my friendly repairman again. Saved a few dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from EL PASO, TX
- Parts Used:
- WP67006331
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the locking latch to the water filter cover had been broken for a while
Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from ALIQUIPPA, PA
- Parts Used:
- W11396037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket torn
Pulled old gasket off door put new one in channel on door pushed gasket in channel less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Hardin, MT
- Parts Used:
- WPW10642944
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I scratched the door handle while moving the refrigerator into my house.
With a small allen wrench, I was able to loosen the two screws to remove the door handle and replace the new on without any problems. A very simple operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney B. from Crestview, FL
- Parts Used:
- W11395888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter stopped up. Causing the refrigerator to make a loud noise. water dispenser didn't work. less than 4.00 fixed all that
Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from EASTON, PA
- Parts Used:
- W11396037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gasket had ripped over the years where they flexed when dooors were opened and closed.
last time i tried it right away after removing from shipping box.. relaxing with with hot air gun... was not to easy... this time i allowed gaskets to relax for a week on a flat surface. in a warm room.... took less than 5 minutes per door.... no hot air needed.... VERY easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Live Oak, FL
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rear mount tab broken on Center Crisper Rail
It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from FSTRVL TRVOSE, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory P from EXPORT, PA
- Parts Used:
- W10882923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice would stick and not dispense
Removed the ice tray with nut driver underneath after removing and unplugging ice machine. Then by remembering, unplugged the necessary electric connectors because electric worked well(replaced electric last time I got a new assembly). Plugged in electric needed, not all (again I'm saying that), then fit back assembly with nut driver underneath.
Was this instruction helpful to you?
Thank you for voting!