59669282001 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- john from CASCADE, IA
- Parts Used:
- WPW10534161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old one broke
snap the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Chelmsford, MA
- Parts Used:
- WPW10280613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken basket hanger
It was easy, remove clips and install new basket hanger and then just clip on the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sonny from Moraga, CA
- Parts Used:
- WP67006878
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass crisper -shelving
The glass shelf sits on top of the crisper housing. That was the problem since when I turned the housing over to clean, the glass fell off. I just had to set the new part on to the housing and it was fixed.
I do want to comment on how easy it was to find the part on your website, how reasonable the price and the quick delivery. Thanks!
I do want to comment on how easy it was to find the part on your website, how reasonable the price and the quick delivery. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Laurel, MD
- Parts Used:
- WP67002633, WPW10671238
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The center crisper rail for the crisper pans broke and one of the bins ended up cracking
I removed the crisper pans, installed the new rail and then installed the new bins. Very easily done--I was finished in 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEANNE M from STONE MTN, GA
- Parts Used:
- WP67006878
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Glass broke when I was cleaning it. Do not take out the shelf with the glass. Clean glass separately
I opened the large cardboard container the way it appeared to have been sealed. I knew i was dealing with glass. It was packed soooo great! After opening I Saw that the glass was tucked behind a separate piece of cardboard. Glad I had laid the package on the table to open. This made it easy to lift up out of the package. I went over the glass with a slightly damp cloth and dried. Peeled off the little stickers and laid it on top of the shelf supports and middle divider. It rested down right on top and eased into place. Wah-la!! All done! Thanks! Easiest repair I have ever had, and I am almost 70 with a lot of history in repairs!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Wilmington, NC
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken center crisper rail
I took all items off the glass shelf. Removed the two crisper drawers. Removed the glass shelf. Installed the center rail. Replaced the two crisper drawers, the glass shelf and all items. Job done in less that 1 min. Thank you for great customer service and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from WYNNEWOOD, PA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rail snapped
Followed video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Reading, AL
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator was not cold.
Refrigerator was not cold.
I had this problem before and it was the control vale in the back of the refrigerator. I ordered it and change that out in 5 minutes. That wasn’t the problem. I had the repairman come over and within 5 minutes he told me what the problem was. He showed me where the control board was. He then walked me through the removal process.
First remove the light cover on the Freezer & Refrigerator in front where the light button is located. Pull down on the front of the light cover. It pops out.
Second, in the front of the freezer & refrigerator temp control panel put your fingertips in front of the panel and pull down it’s hard to get the pins to release but the front pins will release, then pull down a little to allow the back hooks to release. (You can use a small common screwdriver if you can’t get it with your fingertips).
Next, once the panel is removed then disconnect the wiring harness. Then bring the panel to the counter, this is where you remove the circuit card and replace it. There are 4 hooks that hold the circuit board in place. Use a small common screwdriver to push the hooks away from the board. The new board comes as one piece. The board is perforated to allow you to snap the board. Directions come with the board and how to snap it. You will need to pay attention on how you removed the board. You will need to put the new board in the same way it came out.
Once the board is re-installed and lock into position reverse the process and install the control panel back into position.
Next is the programing of the board. Follow the directions that come with the control board and you will be back in business
This task took about 15 minutes to remove & replace and to program.
I had this problem before and it was the control vale in the back of the refrigerator. I ordered it and change that out in 5 minutes. That wasn’t the problem. I had the repairman come over and within 5 minutes he told me what the problem was. He showed me where the control board was. He then walked me through the removal process.
First remove the light cover on the Freezer & Refrigerator in front where the light button is located. Pull down on the front of the light cover. It pops out.
Second, in the front of the freezer & refrigerator temp control panel put your fingertips in front of the panel and pull down it’s hard to get the pins to release but the front pins will release, then pull down a little to allow the back hooks to release. (You can use a small common screwdriver if you can’t get it with your fingertips).
Next, once the panel is removed then disconnect the wiring harness. Then bring the panel to the counter, this is where you remove the circuit card and replace it. There are 4 hooks that hold the circuit board in place. Use a small common screwdriver to push the hooks away from the board. The new board comes as one piece. The board is perforated to allow you to snap the board. Directions come with the board and how to snap it. You will need to pay attention on how you removed the board. You will need to put the new board in the same way it came out.
Once the board is re-installed and lock into position reverse the process and install the control panel back into position.
Next is the programing of the board. Follow the directions that come with the control board and you will be back in business
This task took about 15 minutes to remove & replace and to program.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Lancaster, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
compressor not running
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FORD CITY, PA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer occasionally had a temperature alarm.Clicking noise also.
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from WILMINGTON, MA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken center crisper rail
Lift off glass shelf and insert tabs of rail on each end , replace shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Colorado Springs, CO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer and refrigerator compartments not cold enough
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from GOLDEN, CO
- Parts Used:
- WPW10503278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
About twicw per year the freezer would ice up because the control board didn't activate the defrost element
Removed the cover using a mirror to see how to release the clips on the rear side of the cover, removed the circuit board noting how everything was installed and also visually verified the part was the same. Broke the circuit at the designated score, installed and followed instructions for programming. All is well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from FAIRFIELD, VA
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Unit would not defrost
I checked the element and the thermostat and determined the problem to be the control board. I simply followed the instruction in the video. Everything went well until the last step, the video said to push the freezer down button. When this did not work I refered to the written instructions which told me to push the up button. That did it. Job complete. The unit is working as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothea from TOMS RIVER, NJ
- Parts Used:
- WPW10534161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Easy to clip in place
No tools required, but you must be careful not to shove or jam this kick plate into place as it is a plastic part and not really very sturdy. This is the second time I have replaced the kick plate and PartSelect has always been knowledgeable, polite, and helpful
!!
!!
Was this instruction helpful to you?
Thank you for voting!