59669282001 Kenmore Refrigerator - Instructions

I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!

Just slipped it in. I think it's a very poor design.

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

Bought new crisper from Parts select followed directions on how to replace. Replaced in a bought 30 minutes.

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

The fridge would occasionally run warm, requiring me to turn it off and defrost the evap coils in the freezer. I found an online video that demonstrated the entire process of replacing the control board. The fridge model in the video was different than mine, so it took some time to figure out how to remove the panel. Once that was done, the rest was easy. The only tool required was a flat-head screwdriver that was used to push in the tabs holding the panel in place. The circuit board took more effort to split in two than I had realized, and I had to be careful not to bend any of the components on its surface. The whole process took less than 30 minutes, and the fridge is working properly now..

I unplugged the capacitor which allowed access to the on/off relay. Unplugged the old broken one and plugged in the new one. All better.

got the new part, took the old part out and snapped the new part in! Very easy. Thank you.

I opened the large cardboard container the way it appeared to have been sealed. I knew i was dealing with glass. It was packed soooo great! After opening I Saw that the glass was tucked behind a separate piece of cardboard. Glad I had laid the package on the table to open. This made it easy to lift up out of the package. I went over the glass with a slightly damp cloth and dried. Peeled off the little stickers and laid it on top of the shelf supports and middle divider. It rested down right on top and eased into place. Wah-la!! All done! Thanks! Easiest repair I have ever had, and I am almost 70 with a lot of history in repairs!!

I took all items off the glass shelf. Removed the two crisper drawers. Removed the glass shelf. Installed the center rail. Replaced the two crisper drawers, the glass shelf and all items. Job done in less that 1 min. Thank you for great customer service and quick delivery.

The glass shelf sits on top of the crisper housing. That was the problem since when I turned the housing over to clean, the glass fell off. I just had to set the new part on to the housing and it was fixed.
I do want to comment on how easy it was to find the part on your website, how reasonable the price and the quick delivery. Thanks!

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Lift off glass shelf and insert tabs of rail on each end , replace shelf.

It was easy, remove clips and install new basket hanger and then just clip on the clips.